No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: CCNA
Filter:AllUnanswered
Refer to the exhibit. With which metric was the route to host 172.16.0.202 learned?
Admin asked 1 year ago • 
20 views0 answers0 votes
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their commonEthernet link.The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?
Admin asked 1 year ago • 
23 views0 answers0 votes
A user configured OSPF in a single area between two routers. A serial interface connecting R1 and R2 is running encapsulation PPP. By default, which OSPF network type is seen on this interface when the user types show ip ospf interface on R1 or R2?
Admin asked 1 year ago • 
26 views0 answers0 votes
Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
Admin asked 1 year ago • 
30 views0 answers0 votes
Which MAC address is recognized as a VRRP virtual address?
Admin asked 1 year ago • 
21 views0 answers0 votes
If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?
Admin asked 1 year ago • 
21 views0 answers0 votes
Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Se0/0/0 interfaces on the Atlanta and Washington routers reach one another? (Choose two.)
Admin asked 1 year ago • 
28 views0 answers0 votes
The OSPF Hello protocol performs which of the following tasks? (Choose two.)
Admin asked 1 year ago • 
21 views0 answers0 votes
What are two requirements for an HSRP group? (Choose two.)
Admin asked 1 year ago • 
20 views0 answers0 votes
Which two pieces of information can you learn by viewing the routing table? (Choose two.)
Admin asked 1 year ago • 
16 views0 answers0 votes
Refer to the exhibit. Which route type does the routing protocol Code D represent in the output?
Admin asked 1 year ago • 
24 views0 answers0 votes
An engineer must configure an OSPF neighbor relationship between router R1 and R3. The authentication configuration has been configured and the connecting interfaces are in the same 192.168.1.0/30 subnet. What are the next two steps to complete the configuration? (Choose two.)
Admin asked 1 year ago • 
21 views0 answers0 votes
Refer to the exhibit. A packet is being sent across router R1 to host 172.16.0.14. What is the destination route for the packet?
Admin asked 1 year ago • 
29 views0 answers0 votes
Refer to the exhibit. A packet is being sent across router R1 to host 172.16.3.14. To which destination does the router send the packet?
Admin asked 1 year ago • 
25 views0 answers0 votes
Which command is used to display the collection of OSPF link states?
Admin asked 1 year ago • 
33 views0 answers0 votes
Which two statements about exterior routing protocols are true? (Choose two.)
Admin asked 1 year ago • 
26 views0 answers0 votes
Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router)# network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSP
Admin asked 1 year ago • 
29 views0 answers0 votes
You have two paths for the 10.10.10.0 network – one that has a feasible distance of 3072 and the other of 6144.What do you need to do to load balance your EIGRP routes?
Admin asked 1 year ago • 
24 views0 answers0 votes
Refer to the exhibit. C-router is to be used as a “router-on-a-stick” to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
Admin asked 1 year ago • 
29 views0 answers0 votes
Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency? (Choose two.)
Admin asked 1 year ago • 
21 views0 answers0 votes
« Previous1…5051525354…70Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In