No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: CCNA
Filter:AllUnanswered
Refer to the exhibit. An administrator must connect SW_1 and the printer to the network. SW_2 requires DTP to be used for the connection to SW_1. The printer is configured as an access port with VLAN 5. Which set of commands completes the connectivity?
Anonymous commented 55 years ago • 
166 views0 answers0 votes
After a recent security breach and a RADIUS failure, an engineer must secure the console port of each enterprise router with a local username and password.Which configuration must the engineer apply to accomplish this task?
Admin asked 1 year ago • 
60 views0 answers0 votes
Refer to the exhibit. Load-balanced traffic is coming in from the WAN destined to a host at 172.16.1.190. Which next-hop is used by the router to forward the request?
Anonymous commented 55 years ago • 
128 views0 answers0 votes
Refer to the exhibit. A network engineer started to configure port security on a new switch. These requirements must be met:· MAC addresses must be learned dynamically.· Log messages must be generated without disabling the interface when unwanted traffic is seen.Which two commands must be configured to complete this task? (Choose two.)
Anonymous commented 55 years ago • 
140 views0 answers0 votes
Refer to the exhibit. The given Windows PC is requesting the IP address of the host at www.cisco.com. To which IP address is the request sent?
Anonymous commented 55 years ago • 
58 views0 answers0 votes
Refer to the exhibit. An engineer is configuring a new router on the network and applied this configuration. Which additional configuration allows the PC to obtain its IP address from a DHCP server?
Anonymous commented 55 years ago • 
74 views0 answers0 votes
Refer to the exhibit. Router OldR is replacing another router on the network with the intention of having OldR and R2 exchange routes. After the engineer applied the initial OSPF configuration, the routes were still missing on both devices. Which command sequence must be issued before the clear IP ospf process command is entered to enable the neighbor relationship?
Anonymous commented 55 years ago • 
78 views0 answers0 votes
An administrator is configuring a Cisco Catalyst switch so that it will accept management connections only from hosts in the 203.0.113.0/24 network. Other traffic passing through the switch must transit without interruption. Which two configurations must the engineer apply to the router? (Choose two.)
Anonymous commented 55 years ago • 
48 views0 answers0 votes
Refer to the exhibit. An engineer is checking the routing table in the main router to identify the path to a server on the network. Which route does the router use to reach the server at 192.168.2.2?
Anonymous commented 55 years ago • 
251 views0 answers0 votes
Which command enables HTTP access to the Cisco WLC?
Anonymous commented 55 years ago • 
48 views0 answers0 votes
Which two actions are taken as the result of traffic policing? (Choose two.)
Anonymous commented 55 years ago • 
56 views0 answers0 votes
Refer to the exhibit. What is the next-hop IP address for R2 so that PC2 reaches the application server via EIGRP?
Anonymous commented 55 years ago • 
57 views0 answers0 votes
Refer to the exhibit. An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct, which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two.)
Anonymous commented 55 years ago • 
51 views0 answers0 votes
Refer to the exhibit. All routers in the network are configured correctly, and the expected routes are being exchanged among the routers. Which set of routes are learned from neighbors and installed on router 2?
Anonymous commented 55 years ago • 
60 views0 answers0 votes
Which type of wired port is required when an AP offers one unique SSID, passes client data and management traffic, and is in autonomous mode?
Anonymous commented 55 years ago • 
123 views0 answers0 votes
Refer to the exhibit. Drag and drop the prefix lengths from the left onto the corresponding prefixes on the right. Not all prefixes are used.
Anonymous commented 55 years ago • 
63 views0 answers0 votes
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Anonymous commented 55 years ago • 
49 views0 answers0 votes
Which function does an SNMP agent perform?
Anonymous commented 55 years ago • 
58 views0 answers0 votes
Refer to the exhibit. User traffic originating within site B is failing to reach an application hosted on IP address 192.168.0.10, which is located within site
Anonymous commented 55 years ago • 
52 views0 answers0 votes
Refer to the exhibit. The iPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. Which address must be used?
Anonymous commented 55 years ago • 
135 views0 answers0 votes
123…70Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In