Click the Exhibit button.

You are advertising a summary route that represents your local network (172.20.0.0/16) to both ISP A and ISP

A. You want to influence all traffic sent to you from ISP C to go through R2.
How would you accomplish this task?

B. On R2, change the local preference value to 50.

C. On R1, change the local preference value to 250.

D. On R1, prepend your AS number three times on the 172.20.0.0/16 route when advertising it to ISP 1.

E. On R2, prepend your AS number three times on the 172.20.0.0/16 route when advertising it to ISP 2.

Click the Exhibit button.

Referring to the exhibit, where should next-hop-self-policy be applied to alter the next-hop value?

A. The policy is applied as an export policy for the group ext-64501.

B. The policy is applied as an import policy for the group ext-6450l.

C. The policy is applied as an import policy for the group int-64503.

D. The policy is applied as an export policy for the group int-64503.

Click the Exhibit button.

Referring to the exhibit, what will happen to untagged frames?

A. The untagged frames are associated with VLAN 10.

B. The untagged frames are dropped.

C. The untagged frames are load balanced between VLAN 10 and VLAN 20.

D. The untagged frames are associated with VLAN 20.

Click the Exhibit button.

All devices in the network are configured correctly and the path requirements are valid.
Referring to the exhibit, which two statements are correct? (Choose two.)

A. The primary LSP will be signaled, and its state will be up.

B. The secondary LSP will not be signaled, and its state will be down.

C. The secondary LSP will be signaled, and its state will be up.

D. The primary LSP will not be signaled, and its state will be down.

Click the Exhibit button.

Routers R1 and R4 have a VRRP priority of 90. while R2 and R3 have default VRRP priorities.
Referring to the exhibit, which router will be elected as the primary VRRP router?

A. R1

B. R2

C. R3

D. R4

Which two interface types are used as tunnel endpoints? (Choose two.)

A. ge

B. ae

C. gr

D. ip

Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSA ASBR into the backbone?

A. Type 5

B. Type 3

C. Type 1

D. Type 7

Which two statements are correct about the BGP next-hop attribute value? (Choose two.)

A. By default, the next-hop value Is changed across EBGP links.

B. By default, the next-hop value Is not changed across IBGP links.

C. By default, the next-hop value Is not changed across EBGP links.

D. By default, the next-hop value is changed across IBGP links.

Which OSPF database packet determines which router is in charge of the database synchronization and the transferring of LSA headers between the two systems?

A. link-state request

B. database description

C. hello

D. link-state update

You are deploying an MC-LAG connection at the edge of your network to a new customer. This solution must ensure that traffic uses all available links when forwarding traffic between the two networks.
In this scenario, which two statements are correct? (Choose two.)

A. Transit traffic sent between the two PE devices will use the ICL interface.

B. You must use active/active mode when defining the MC-LAG bundle.

C. You must use active/standby mode when defining the MC-LAG bundle.

D. Transit traffic sent between the two PE devices will use the bundle’s member interfaces.

Click the Exhibit button.

Which type of load balancing is shown in the exhibit?

A. network load balancing

B. elastic load balancing

C. per-flow load balancing

D. per-packet load balancing

Click the Exhibit button.

You confirm that the R2 and R3 routers are receiving a BGP route to the 203 0.113.0/24 network, but both routers display the route as hidden.
Referring to the exhibit, which two actions solve this problem? (Choose two.)

A. Apply the routing policy on R1 as an import policy to the IBGP group.

B. Configure a routing policy on R1 that sets the next hop for the 203 0.113.0/24 BGP route to the IP address that R1 uses for IBGP peering.

C. Configure a routing policy on R1 that sets the next hop for the 203.0.113.0/24 BGP route to the IP address that R1 uses for EBGP peering.

D. Apply the routing policy on R1 as an export policy to the IBGP group.

What are three types of MPLS routers? (Choose three.)

A. transit routers

B. egress routers

C. peering routers

D. aggregation routers

E. ingress routers

Click the Exhibit button.

You have an established LSP between your R1 and R5 devices using the configuration shown in the exhibit. You are asked to ensure that MPLS labels are used to forward traffic by all devices within the LSP.
Which action will accomplish this behavior?

A. Configure the ultimate-hop-popping statement under the R1_TO_R5 label switched path on R1.

B. Configure the explicit-null statement under the protocol mpls hierarchy on R1.

C. Configure the install statement under the R1_TO_R5 label switched path on R1.

D. Delete the no-cspf statement under the R1_TO_R5 label switched path on R1.

Click the Exhibit button.

Which statement is correct about the configuration shown in the exhibit?

A. This policy will reject all prefixes because it does not end with a then accept statement.

B. The NEXT_HOP_SELF policy must also be applied to the group called CUSTOMER_A for bidirectional communication to succeed.

C. This router will take prefixes learned from external BGP and change the BGP next hop to itself before re-advertising them to IBGP peers.

D. This router will take prefixes learned from internal BGP and change the BGP next hop to itself before re-advertising them to EBGP peers.

Click the Exhibit button.

Which two statements are correct about the information shown in the exhibit? (Choose two.)

A. The switch has a bridge priority of 8k.

B. This switch is the root bridge for this spanning tree topology.

C. The root bridge is reachable using the ge-0/0/14 interface.

D. The root bridge’s priority is 4k.

You want to enable a routing platform with redundant REs to switch from a primary RE to a backup RE without alerting peer nodes.
Which two technologies would you use to satisfy this requirement? (Choose two.)

A. NSR

B. ISSU

C. GRES

D. VRRP

Interface ge-0/0/0.0 connects your network to your ISP. You want to advertise this interface address as an internal route in OSPF without creating a neighbor with your ISP.
In this scenario, how is this task accomplished?

A. Remove interface ge-0/0/0.0 from OSPF.

B. Add ge-0/0/0.0 as a passive interface in OSPF.

C. Create a generated route for interface ge-0/0/0.0.

D. Configure a static route for interface ge-0/0/0.0

Click the Exhibit button.

You are asked to configure the OSPF environment to prevent the DRother routers from participating in OR/BDR election.
Referring to the exhibit, which command will accomplish this task?

A. set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type p2p

B. set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority 255

C. set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 0

D. set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma

You are implementing traffic engineering in your MPLS network. You must ensure that the MPLS routes are used to traverse your network. Your solution should not affect IGP routes in your route tables.
In this scenario, which traffic engineering setting will accomplish this behavior?

A. bgp-igp-both-ribs

B. mpls-forwarding

C. bgp-igp

D. bgp

You are asked to create connections between routing instances on the same Junos device and route between the connected instances.
What are two ways to accomplish this task? (Choose two.)

A. Use loopback interfaces.

B. Use an IRB interface.

C. Use logical tunnel Interfaces.

D. Use physical interfaces.

You are adding an IPv6 configuration to an interface on a Junos device.
In this scenario, which statement is correct?

A. The link local address is automatically created using the MAC address within the fd00::/8 prefix range.

B. The link local address must be manually configured within the fd00::/8 prefix range.

C. The link local address is automatically created using the MAC address within the fe80::/l0 prefix range.

D. The link local address must be manually configured within the fe80::/10 prefix range.

Which statement is true about the BGP active state?

A. The BGP active state is the initial state where all BGP traffic is refused.

B. The BGP active state is when BGP attempts to acquire a peer by initiating a TCP connection.

C. The BGP active state is when BGP waits for the TCP connection to be established.

D. The BGP active state is when BGP exchanges update, notification, and keepalive messages with its peer.

Which two statements are correct about BGP? (Choose two.)

A. IBGP neighbors must use the same AS number.

B. By default, the TTL on product-related packets for external neighbors is set to 1.

C. EBGP neighbors must use the same AS number.

D. By default, the TTL on protocol-related packets for internal neighbors is set to 1.

What are three well-known mandatory BGP attributes? (Choose three.)

A. MED

B. origin

C. community

D. AS path

E. next hop

Click the Exhibit button.

All devices in the network are configured correctly and the path requirements are valid.
Referring to the exhibit, which two statements are correct? (Choose two.)

A. The secondary LSP using the via-R2-R4 path will not be signaled, and its state will be down.

B. The secondary LSP using the any-path path will be signaled, and its state will be up.

C. The secondary LSP using the any-path path will not be signaled, and its state will be down.

D. The secondary LSP using the via-R2-R4 path will be signaled, and its state will be up.

What are two types of SIDs used in segment routing? (Choose two.)

A. node

B. link

C. interface

D. adjacency

What are two requirements for a unified in-service software upgrade? (Choose two.)

A. Bidirectional Forwarding Detection must be enabled on the device.

B. Nonstop active routing must be enabled on the device.

C. The device must have dual Routing Engines.

D. The device must be part of the chassis cluster.

Click the Exhibit button.

Which two statements are correct about the actions taken as the packet traverses the service provider MPLS network from Site1 to Site2 as shown in the exhibit? (Choose two.)

A. R1 will perform a lookup using the inet.3 table.

B. R1 will perform a lookup using the mpls.0 table.

C. R2 will perform a lookup using the mpls.0 table.

D. R2 will perform a lookup using the inet.3 table.

Which two statements are correct about the behavior of IS-IS metrics? (Choose two.)

A. Wide metrics enable interfaces to advertise metrics larger than 63.

B. By default, the metric of an interface is calculated based on the speed of the interface.

C. Wide metrics enable an interface to advertise different metrics at Level 1 and Level 2.

D. By default, all physical interfaces have a metric of 10.

You are deploying link aggregation groups.
By default, what are two considerations in this scenario? (Choose two.)

A. There should only be four member links per LAG.

B. Member links are required to be contiguous ports.

C. Member links can reside on different members within an MC-LAG.

D. All the ports must have the same speed.

Which two statements are correct about segment routing? (Choose two.)

A. Segment routing adjacencies require very little resources to maintain.

B. Label assignments can be advertised through OSPF updates.

C. There are no segment routing adjacencies to maintain.

D. Label assignments can be advertised through LDP updates.

An OSPF router does not have a router ID configured.
In this scenario, which statement is correct about the router ID?

A. The Junos OS will use the IP address assigned to the interface with the lowest MAC address.

B. The Junos OS will use the IP address assigned to the loopback interface for the router ID.

C. A router ID will not be assigned until it is manually configured.

D. The Junos OS will use the IP address assigned to the interface with the highest priority.

Which two statements are correct about the way that BGP propagates routes by default? (Choose two.)

A. A route learned by EBGP will be re-advertised to IBGP peers.

B. A route learned by IBGP will not be re-advertised to IBGP peers.

C. A route learned by IBGP will be re-advertised to IBGP peers.

D. A route learned by EBGP will not be re-advertised to IBGP peers.

Click the Exhibit button.

Referring to the exhibit, which two statements are correct? (Choose two.)

A. Devices in AS 65512 will prefer ISP A for traffic destined to the 172.20.0.0/24 network.

B. Devices in AS 65512 will prefer ISP A for traffic destined to the 172.20.21.0/24 network.

C. Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.0.0/24 network.

D. Devices in AS 65512 will prefer ISP B for traffic destined to the 172.20.21.0/24 network.

What is a key differentiator of generate routes from aggregate routes?

A. Generate routes cannot be used as a gateway of last resort.

B. Generate routes use a forwarding next hop.

C. Generate routes have a default next-hop value of reject.

D. Generate routes have a default preference value of 210.

Referring to the exhibit, which two statements are correct? (Choose two.)

A. Traffic ingressing ge-0/0/0 that is tagged with VLAN 100 will be dropped.

B. Traffic ingressing ge-0/0/0 that is tagged with VLAN 200 will egress ge-0/0/1 with an outer VLAN tag of 200.

C. Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 with an outer VLAN tag of 200.

D. Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.

You are asked to configure an ISP which uses the OSPF link state database for path computations.
Which two statements are correct in this scenario? (Choose two.)

A. Traffic engineering extensions are enabled by default in OSPF.

B. You must use the no-cspf parameter in the label-switched-path configuration.

C. You must use the policing parameter in the label-switched-path configuration.

D. Traffic engineering extensions are not enabled by default in OSPF.

Click the Exhibit button.

Referring to the exhibit, which two additional steps should you take to fully configure NSR? (Choose two.)

A. You should configure the max period for NSR precision timers.

B. You must configure graceful restart.

C. You should configure commit synchronization.

D. You must configure GRES.

Click the Exhibit button.

The routers shown in the exhibit are configured for segment routing.
In this scenario, what is the adjacency SID that Router B advertises to Router A?

A. 11

B. 10.1.1.2

C. 10.1.1.1

D. 12

You have created a routing instance named vr3 that will provide access to Server2 (10.0.0.2) for the hosts on the 10.10.10.0/24 network.
Which command would you use to test connectivity between vr3 and Server2?

A. user@router1> ping 10.0.0.2 count 5

B. user@vr3> ping 10.0.0.2 count 5

C. user@vr3> ping 10.0.0.2 count 5 source 10.10.10.1

D. user@router1> ping 10.0.0.2 routing-instance vr3 count 5

Which new field is added to an IPv6 header as compared to IPv4?

A. flow label

B. checksum

C. fragment offset

D. version

When would you use the qualified-next-hop statement with a static route?

A. You can use it to install the static route into different routing tables.

B. You can use it to send unwanted traffic to a null route.

C. You can use it to specify multiple next hops with different preferences.

D. You can use it to resolve the next hop if the next hop is not directly connected.

Which statement describes integrated routing and bridging (IRB) interfaces?

A. An IRB interface enables Layer 2 switching on the router.

B. An IRB interface assigns interfaces to VLANs.

C. An IRB interface is an IP gateway for hosts of a bridge domain.

D. An IRB interface defines a bridge domain.

Which address is used by OSPF hello packets?

A. 224.0.0.5 using multicast

B. 255.0.0.5 using multicast

C. 225.0.0.5 using unicast

D. 224.0.0.5 using unicast

Click the Exhibit button.

Referring to the exhibit, which two statements are correct? (Choose two.)

A. Traffic ingressing ge-1/0/0 that is tagged with VLAN 200 will be dropped.

B. Traffic ingressing ge-1/0/0 that is tagged with VLAN 100 will be dropped.

C. Traffic ingressing ge-1/0/0 that is tagged with VLAN 100 will egress ge-1/0/4 with an outer VLAN tag of 200.

D. Traffic ingressing ge-1/0/0 that is tagged with VLAN 200 will egress ge-1/0/4 with an outer VLAN tag of 200.

You are bringing a new network online with three IS-IS routers using default Junos election priorities. The routers are configured as Level 2 only IS-IS routers.
Which statement is true about the DIS election in this scenario?

A. The router with the highest numerical lo0 IP address will be elected as the DIS.

B. The router with the lowest MAC address will be elected as the DIS.

C. The router with the lowest numerical lo0 IP address will be elected as the DIS.

D. The router with the highest MAC address will be elected as the DIS.

Which two statements are correct about the community BGP attribute on a Junos device? (Choose two.)

A. If the community attribute is present, it Is ignored and deleted in the BGP updates.

B. If the community attribute is present, it should be passed unchanged in the BGP updates.

C. The community attribute is a mandatory BGP attribute.

D. The community attribute is an optional BGP attribute.

Click the Exhibit button.

Referring to the exhibit. Internal BGP between R1 and R2 is not establishing.
What is the problem in this scenario?

A. R1 needs to be configured with an explicit router ID.

B. R1 and R2 must each have unique AS numbers.

C. R1 does not have a route to 192.168.200.2.

D. R1 needs to be configured with a next-hop self policy.

Click the Exhibit button.

Referring to the exhibit, which statement is correct?

A. R1 will advertise only the 10.200.2.0/24 prefix to the 192.168.1.5 neighbor.

B. R1 will advertise only the 10.200.3.0/24 prefix to the 192.168.1.5 neighbor.

C. R1 will advertise the 10.200.1.0/24, 10.200.2.0/24, and 10.200.3.0/24 prefixes to the 192.168.1.5 neighbor.

D. R1 will advertise only the 10.200.1.0/24 prefix to the 192.168.1.5 neighbor.