No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: JN0-102
Filter:AllUnanswered
— Exhibit — [edit routing-options] user@router# show static { route 0.0.0.0/0 { next-hop 10.1.1.1; qualified-next-hop 10.1.1.254 { preference 4; } } } — Exhibit — Assuming both paths shown in the exhibit are available, which statement is correct?
Admin asked 8 months ago • 
17 views0 answers0 votes
Which command prompt indicates that you are in operational mode?
Admin asked 8 months ago • 
35 views0 answers0 votes
What is the default action for firewall filters?
Admin asked 8 months ago • 
20 views0 answers0 votes
— Exhibit — [edit interfaces ge-0/0/1] user@router# show unit 100 { vlan-id 100; family inet { address 10.1.1.1 /24; } } [edit interfaces ge-0/0/1] user@router# commit check [edit interfaces ge-0/0/1] 'unit 100' Only unit 0 is valid for this encapsulation error: configuration check-out failed — Exhibit — Referring to the exhibit, you are unable to commit the configuration for the ge-0/0/1 interface. What must you do to commit the configuration?
Admin asked 8 months ago • 
19 views0 answers0 votes
— Exhibit — user@router> restart ^ unknown command. — Exhibit — You are investigating routing problems on a device running the Junos OS. You receive the error shown in the exhibit when you attempt to restart the routing process. Which statement describes the problem?
Admin asked 8 months ago • 
55 views0 answers0 votes
— Exhibit — [edit interfaces ge-0/0/6] user@router# show unit 0 { familyinet { address 172.16.10.100/24; address 172.16.10.101/24; } } — Exhibit — You have two IP addresses configured on the ge-0/0/6 interface, as shown in the exhibit. You want to select the 172.16.10.101 address as the source address for packets sent from this interface to hosts on a remote subnet. Which parameter would you add to the 172.16.10.101 address to…
Admin asked 8 months ago • 
18 views0 answers0 votes
Which information would you find using the CLI help function? (Choose two.)
Admin asked 8 months ago • 
13 views0 answers0 votes
Which process is responsible for the routing protocols on a Junos device?
Admin asked 8 months ago • 
44 views0 answers0 votes
What is the central processing component of the forwarding plane?
Admin asked 8 months ago • 
17 views0 answers0 votes
What is the network address for the 10.13.147.100/19 host?
Admin asked 8 months ago • 
14 views0 answers0 votes
Which command will display the active configuration?
Admin asked 8 months ago • 
52 views0 answers0 votes
Which two statements are true about TCP communication? (Choose two.)
Admin asked 8 months ago • 
18 views0 answers0 votes
At which command prompt would you issue the set date command?
Admin asked 8 months ago • 
24 views0 answers0 votes
At which layer of the OSI model does error checking occur with IPv6?
Admin asked 8 months ago • 
14 views0 answers0 votes
Which interface type connects the control and forwarding planes on an MX Series device?
Admin asked 8 months ago • 
13 views0 answers0 votes
— Exhibit — user@router> show route protocol static inet.0: 15 destinations, 15 routes (15 active, 0 holddown, 0 hidden) + = Active Route, – = Last Active, * = Both 99.0.0.0/17 *[Static/5] 00:00:11 >to 10.1.1.2 via ge-0/0/1.0 99.0.0.0/19 *[Static/5] 00:00:11 >to 10.1.2.2 via ge-0/0/2.0 99.0.0.0/24 *[Static/5] 00:00:11 >to 10.1.3.2 via ge-0/0/3.0 99.0.0.0/26 *[Static/5] 00:00:11 >to 10.1.4.2 via ge-0/0/4.0 — Exhibit — In the exhibit, there are four static routes that…
Admin asked 8 months ago • 
17 views0 answers0 votes
Which command is used to load the rescue configuration?
Admin asked 8 months ago • 
11 views0 answers0 votes
What are three characteristics of UDP? (Choose three.)
Admin asked 8 months ago • 
13 views0 answers0 votes
— Exhibit — user@router> show configuration groups { ge-int { interfaces { { unit 0 { familyinet { address 10.10.12.1/24; } } } } } } … interfaces { ge-0/0/1 { unit 0; } — Exhibit — Referring to the exhibit, which two actions would you take to only apply the 10.10.12.1/24 address to the ge-0/0/1.0 interface?
Admin asked 8 months ago • 
48 views0 answers0 votes
What must you type to enter operational mode from the root@% command prompt?
Admin asked 8 months ago • 
21 views0 answers0 votes
« Previous1234Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In