No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: 350-801
Filter:AllUnanswered
An engineer must configure switch port 2/8 to send CDP packets to configure an attached Cisco IP phone to trust tagged traffic on its access port. Which command is required to complete the configuration? Router# configure terminal – Router(config)# interface gigabitethernet 2/8 Router(config-if)# description Cube E43.308-6491
Admin asked 10 months ago • 
13 views0 answers0 votes
What are two characteristics of QoS Traffic shaping? (Choose two.)
Admin asked 10 months ago • 
16 views0 answers0 votes
Where in Cisco UCM is restrictions on audio bandwidth configured?
Admin asked 10 months ago • 
18 views0 answers0 votes
Refer to exhibit. An engineer configured a codec preference list on a Cisco Unified Border Element. Which command is required on the dial peer to ensure that all codecs are offered during an early offer call?
Admin asked 10 months ago • 
17 views0 answers0 votes
What is the importance of locations when using location-based CAC within Cisco UCM?
Admin asked 10 months ago • 
18 views0 answers0 votes
What is the function of the Cisco Unity Connection Call Handler?
Admin asked 10 months ago • 
16 views0 answers0 votes
What is a capability of a DNS server?
Admin asked 10 months ago • 
14 views0 answers0 votes
Refer to the exhibit. An engineer must implement toll fraud prevention on a Cisco UCM cluster by allowing only the indicated IP address and protocols through Cisco Unified Border Element. What must be configured?
Admin asked 10 months ago • 
29 views0 answers0 votes
How does an administrator ensure compliance with ITU-T G.114 latency requirements when deploying voice and video applications over routes that include a geostationary satellite?
Admin asked 10 months ago • 
15 views0 answers0 votes
What is a function of a call handler in Cisco Unity Connection?
Admin asked 10 months ago • 
19 views0 answers0 votes
How does WRED prevent congestion?
Admin asked 10 months ago • 
18 views0 answers0 votes
Refer to the exhibit. An engineer must deploy a Cisco Unified Border Element that will allow the last four digits of a dialed number to be sent from the Cisco Unified Border Element to Cisco UCM. The configuration in the exhibit already exists on die Cisco Unified Border Element. Which additional configuration must be performed on the Cisco Unified Border Element?
Admin asked 10 months ago • 
20 views0 answers0 votes
Which two media encryptions should be used when configuring SRTP between Cisco UCM and Cisco VCS Expressway? (Choose two.)
Admin asked 10 months ago • 
18 views0 answers0 votes
Refer to the exhibit. An engineer must implement toll fraud prevention on a Cisco UCM cluster. Only the SIP protocol must be allowed for connections passing through Cisco Unified Border Element. What must be configured?
Admin asked 10 months ago • 
13 views0 answers0 votes
Refer to the exhibit. An engineer configured NTP on Cisco UCM and runs the utils ntp status command from Cisco UCM CLI and receives an error message. How is this issue mitigated and fixed?
Admin asked 10 months ago • 
33 views0 answers0 votes
Where would an administrator update learned patterns from the DNA UI?
Admin asked 10 months ago • 
15 views0 answers0 votes
Refer to the exhibit. CUBE_1 and CUBE_2 must use the G.729r8 codec when communicating. Which action completes the configuration?
Admin asked 10 months ago • 
20 views0 answers0 votes
An engineer must configure a DHCP server to save automatic bindings on a remote host that has an IP address of 172.16.1 1. The IP address range of 172.16.1.103 to 172.16.1.106 must be blocked from the DHCP server. Which set of commands must the engineer run?
Admin asked 10 months ago • 
26 views0 answers0 votes
Refer to the exhibit. An engineer is integrating Cisco UCM with Cisco Unity Connection via SIP. Which two boxes should be checked to complete the configuration of the SIP trunk security profile? (Choose two.)
Admin asked 10 months ago • 
20 views0 answers0 votes
Why does Cisco UCM use DNS?
Admin asked 10 months ago • 
16 views0 answers0 votes
« Previous1…45678…23Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In