No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: 300-425
Filter:AllUnanswered
Which non-Wi-Fi interferer can be identified by Metageek Chanalyzer?
Admin asked 9 months ago • 
21 views0 answers0 votes
A wireless engineer is using Ekahau Site Survey to validate that an existing wireless network is operating as expected. Which type of survey should be used to identify the end-to-end network performance?
Admin asked 9 months ago • 
13 views0 answers0 votes
A wireless engineer is hired to design a network for a technology company. The company campus has four buildings and a warehouse with access points that provide full wireless coverage as well as a pair of WLCs located in the core of the network. Which type of wireless architecture is being used?
Admin asked 9 months ago • 
16 views0 answers0 votes
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. What is the minimum requirement for the design?
Admin asked 9 months ago • 
23 views0 answers0 votes
A high-density wireless network is designed. Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectrum?
Admin asked 9 months ago • 
23 views0 answers0 votes
Which two criteria must be considered when conducting an outdoor bridge site survey? (Choose two.)
Admin asked 9 months ago • 
16 views0 answers0 votes
Where must the APs be mounted when used in a high-density wireless network to provide 6 dB to 20 dB of attenuation to a cell?
Admin asked 9 months ago • 
19 views0 answers0 votes
Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)
Admin asked 9 months ago • 
20 views0 answers0 votes
An engineer must perform a pre deployment site survey for a new building in a high-security area. The design must provide a primary signal RSSI of -65 dBm for the clients. Which two requirements complete this design? (Choose two.)
Admin asked 9 months ago • 
20 views0 answers0 votes
As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which two areas is the engineer most likely to find sources of 2.4 GHz and 5 GHz RF noise? (Choose two.)
Admin asked 9 months ago • 
19 views0 answers0 votes
An engineer is designing a high-density WLAN for a 10,000-seat auditorium. The solution must take advantage of human attenuation, as well as the aesthetics of the room. Where must the APs be placed?
Admin asked 9 months ago • 
14 views0 answers0 votes
An engineer is designing a new wireless network. The network needs to fulfill the following requirements: ✑ support multimedia applications ✑ support a high concentration of wireless clients ✑ support data over wireless ✑ support roaming Which approach should be used?
Admin asked 9 months ago • 
78 views0 answers0 votes
An engineer performs a Layer 1 survey by using Metageek Chanalyzer only on the current operating channel. Which operating mode is configured for a Cisco CleanAir AP?
Admin asked 9 months ago • 
19 views0 answers0 votes
An engineer is designing a wireless network to support Cisco Hyperlocation. The customer indicated some locations that require high density. How is the design adjusted?
Admin asked 9 months ago • 
19 views0 answers0 votes
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?
Admin asked 9 months ago • 
15 views0 answers0 votes
An engineer changed the TPC Power Threshold for a wireless deployment from the default value to -65 dBm. The engineer conducts a new post deployment survey to validate the results. What is the expected outcome?
Admin asked 9 months ago • 
26 views0 answers0 votes
A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)
Admin asked 9 months ago • 
15 views0 answers0 votes
A wireless engineer is designing a wireless network for a warehouse using access points with internal antennas. Which two elements have a negative effect on the wireless users? (Choose two.)
Admin asked 9 months ago • 
21 views0 answers0 votes
How are mobility groups created, excluding mobility anchors?
Admin asked 9 months ago • 
23 views0 answers0 votes
Clustering Cisco WLCs into a single RF group enables the RRM algorithms to scale beyond the capabilities of a single Cisco WLC. How many WLCs and APs in an RF group can the controller software scale up to in WLC release 8.9 depending on the platform?
Admin asked 9 months ago • 
13 views0 answers0 votes
« Previous123456…9Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In