No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: 300-410
Filter:AllUnanswered
How do devices operate in MPLS L3VPN topology?
Admin asked 10 months ago • 
37 views0 answers0 votes
Refer to the exhibit. The engineer is reviewing the logs on the DENVER router and notices that this error message repeats constantly: *Jun 12 13:42:03.399: %TCP-6-BADAUTH: No MD5 digest from 10.40.1.1(27174) to 10.40.1.2(179) tableid – 0 Which action resolves the issue?
Admin asked 10 months ago • 
29 views0 answers0 votes
Which Layer 3 VPN attribute allows different customers to connect to the same MPLS network with overlapping IP ranges?
Admin asked 10 months ago • 
28 views0 answers0 votes
Refer to the exhibit. An engineer configured IP SLA to monitor a next hop on a router for reachability. When the next hop is unreachable, the router is executing tracking and falling over another route, but packet loss is experienced because the reachability is flapping. Which action resolves the issue?
Admin asked 10 months ago • 
28 views0 answers0 votes
Refer to the exhibit. The services at branch B are down. An engineer notices that router A and router B are not exchanging any routes. Which configuration resolves the issue on router B?
Admin asked 10 months ago • 
31 views0 answers0 votes
What is the use of IPv6 snooping?
Admin asked 10 months ago • 
20 views0 answers0 votes
Refer to the exhibit. An engineer must troubleshoot a connectivity issue impacting the redistribution of the subnet 172.16.2.48/28 into the OSPF domain. Which configuration on router R1 advertises this subnet into the OSPF domain?
Admin asked 10 months ago • 
26 views0 answers0 votes
SIMULATION – Guidelines – This is a lab item in which tasks will be performed on virtual devices. • Refer to the Tasks tab to view the tasks for this lab item. • Refer to the Topology tab to access the device console(s) and perform the tasks. • Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window. •…
Admin asked 10 months ago • 
31 views0 answers0 votes
Which feature drops packets if the source address is not found in the snooping table?
Admin asked 10 months ago • 
25 views0 answers0 votes
Refer to the exhibit. An engineer must advertise LAN network 192.168.1.0 of router A to router B through OSPF. The engineer notices that router B was configured, but the LAN network of router A is not in the routing table of router B. Which configuration on router A resolves the problem?
Admin asked 10 months ago • 
25 views0 answers0 votes
Refer to the exhibit. R1 is multihomed to ISP1 and ISP2. uRPF strict mode has been configured on both interfaces uplinked to the ISPs. Traffic destined to the Internet over ISP1 returns to R1 via ISP2 and is immediately dropped. Which configuration changes address this issue and allow return traffic from the other ISP?
Admin asked 10 months ago • 
28 views0 answers0 votes
Refer to the exhibit. Routers R1 and R2 exchange routes to each other's loopback through OSPF. Telnet traffic must be blocked from R2 Lo0 to R1 Lo2. Which configuration resolves the issue?
Admin asked 10 months ago • 
49 views0 answers0 votes
Refer to the exhibit. After an engineer configured a new Cisco router as a DHCP server, users reported two primary issues: • Devices in the HR subnet have intermittent connectivity problems. • Workstations in the LEGAL subnet cannot obtain IP addresses. Which configurations must the engineer apply to ROUTER_1 to restore connectivity for the affected devices?
Admin asked 10 months ago • 
39 views0 answers0 votes
What are the two benefits of using BFD? (Choose two.)
Admin asked 10 months ago • 
27 views0 answers0 votes
Refer to the exhibit. The default route from R1 must be withdrawn from the routing table if R1 cannot ping 10.1.1.1, but it is not working correctly. Which configuration resolves the issue?
Admin asked 10 months ago • 
27 views0 answers0 votes
Refer to the exhibit. An engineer must troubleshoot an issue affecting the communication from router R2 to the TACACS server. Which configuration resolves the issue?
Admin asked 10 months ago • 
27 views0 answers0 votes
What is the purpose of the DHCPv6 Guard?
Admin asked 10 months ago • 
23 views0 answers0 votes
Refer to the exhibit. An engineer configured SNMP in R1 to be able to save and upload configurations to the SNMP server but failed when they tried to backup R1 configuration on the server. Which configuration resolves the issue?
Admin asked 10 months ago • 
34 views0 answers0 votes
An engineer must configure encrypted packets for a single router OSPF neighborship. Which configuration meets this requirement?
Admin asked 10 months ago • 
23 views0 answers0 votes
What are two features of BFD? (Choose two.)
Admin asked 10 months ago • 
24 views0 answers0 votes
« Previous1234…32Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In