No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: 300-115
Filter:AllUnanswered
What command would be used to display detailed information regarding VRRP groups on the switch?
Admin asked 9 months ago • 
49 views0 answers0 votes
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration. You are adding new VLANs. VLAN500 and VLAN600 to the topology in such way that you need to configure SW1 as primary root for VLAN 500 and secondary for VLAN 600 and SW2 as primary root for VLAN…
Anonymous commented 55 years ago • 
53 views0 answers0 votes
Instructions: ✑ Enter IOS commands on the device to verify network operation and answer the multiple-choice questions. ✑ THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. ✑ Click on R1 and R2 to gain access to the consoles of these devices. No console or enable passwords are required. ✑ To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. ✑ There are four multiple-choice…
Anonymous commented 55 years ago • 
124 views0 answers0 votes
If a switch that is configured globally with DHCP snooping receives a packet that has DHCP option-82 set to 192.168.1.254, how does the switch handle the packet?
Admin asked 9 months ago • 
37 views0 answers0 votes
What command provides the output shown below?
Anonymous commented 55 years ago • 
39 views0 answers0 votes
You have been asked to install and configure a new switch in a customer network. Use the console access to the existing and new switches to configure and verify correct device configuration. Refer to the configuration. For which configured VLAN are untagged frames sent over trunk between SW1 and SW2?
Anonymous commented 55 years ago • 
39 views0 answers0 votes
You have configured switches A and B in a network. The gigabitethernet0/1 interface of switch A has HSRP enabled on it for VLAN 30. Switch A has a priority of 240 and switch B has a priority of 200 for the HSRP group. You want to ensure that if the gigabitethernet0/1 interface of switch A goes down, then switch B becomes the active HSRP switch for the VLANs. You have…
Anonymous commented 55 years ago • 
43 views0 answers0 votes
Instructions: ✑ Enter IOS commands on the device to verify network operation and answer the multiple-choice questions. ✑ THIS TASK DOES NOT REQUIRE DEVICE CONFIGURATION. ✑ Click on R1 and R2 to gain access to the consoles of these devices. No console or enable passwords are required. ✑ To access the multiple-choice questions, click on the numbered boxes on the left of the top panel. ✑ There are four multiple-choice…
Anonymous commented 55 years ago • 
124 views0 answers0 votes
Refer to the exhibit. Which EtherChannel negotiation protocol is configured on the interface f0/13 f0/15?
Anonymous commented 55 years ago • 
34 views0 answers0 votes
What are two advantages of LLDP over Cisco Discovery Protocol? (Choose two.)
Admin asked 9 months ago • 
27 views0 answers0 votes
Which two commands configure SPAN to monitor outgoing traffic across multiple interfaces? (Choose two.)
Admin asked 9 months ago • 
24 views0 answers0 votes
Which command should you enter to configure a device as an NTP server?
Admin asked 9 months ago • 
24 views0 answers0 votes
Which two commands configure SPAN to monitor incoming traffic across multiple interfaces? (Choose two.)
Admin asked 9 months ago • 
25 views0 answers0 votes
Which three commands configure RSPAN to capture outgoing traffic from one VLAN on an interface while ignoring other VLAN traffic on the same interface? (Choose three.)
Admin asked 9 months ago • 
20 views0 answers0 votes
Which two statements about VTP modes are true? (Choose two.)
Admin asked 9 months ago • 
29 views0 answers0 votes
Which HSRP identifier can an end station use to find the default gateway at the data link layer?
Admin asked 9 months ago • 
24 views0 answers0 votes
How is the AAA accounting feature used with RADIUS?
Admin asked 9 months ago • 
25 views0 answers0 votes
Which command removes all MAC addresses on a port channel?
Admin asked 9 months ago • 
26 views0 answers0 votes
Which two values do you configure on a switch to authenticate a RADIUS server? (Choose two.)
Admin asked 9 months ago • 
22 views0 answers0 votes
Which two commands enable loop guard on A Cisco switch? (Choose two.)
Admin asked 9 months ago • 
34 views0 answers0 votes
123…50Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In