No Result
View All Result
Quesions Library
Contribute
No Result
View All Result
No Result
View All Result

 


Questions › Category: 200-301
Filter:AllUnanswered
Refer to the exhibit. A network engineer must configure communication between PC A and the File Server. To prevent interruption for any other communications, which command must be configured?
Admin asked 9 months ago • 
21 views0 answers0 votes
Refer to the exhibit. An engineer is configuring a Layer 3 port-channel interface with LACP. The configuration on the first device is complete, and it is verified that both interfaces have registered the neighbor device in the CDP table. Which task on the neighbor device enables the new port channel to come up without negotiating the channel?
Admin asked 9 months ago • 
33 views0 answers0 votes
Refer to the exhibit. What is the result if Gig1/11 receives an STP BPDU?
Admin asked 9 months ago • 
16 views0 answers0 votes
Refer to the exhibit. Which configuration establishes a Layer 2 LACP EtherChannel when applied to both switches?
Admin asked 9 months ago • 
25 views0 answers0 votes
Which access layer threat-mitigation technique provides security based on identity?
Admin asked 9 months ago • 
15 views0 answers0 votes
Refer to the exhibit. Which action do the switches take on the trunk link?
Admin asked 9 months ago • 
25 views0 answers0 votes
A network engineer must configure two new subnets using the address block 10.70.128.0/19 to meet these requirements: ✑ The first subnet must support 24 hosts. ✑ The second subnet must support 472 hosts. ✑ Both subnets must use the longest subnet mask possible from the address block. Which two configurations must be used to configure the new subnets and meet a requirement to use the first available address in each…
Admin asked 9 months ago • 
30 views0 answers0 votes
Which protocol does an access point use to draw power from a connected switch?
Admin asked 9 months ago • 
19 views0 answers0 votes
An administrator must secure the WLC from receiving spoofed association requests. Which steps must be taken to configure the WLC to restrict the requests and force the user to wait 10 ms to retry an association request?
Admin asked 9 months ago • 
19 views0 answers0 votes
Refer to the exhibit. Only four switches are participating in the VLAN spanning-tree process. Branch-1: priority 614440 – Branch-2: priority 39391170 – Branch-3: priority 0 – Branch-4: root primary – Which switch becomes the permanent root bridge for VLAN 5?
Admin asked 9 months ago • 
21 views0 answers0 votes
An engineer must configure traffic for a VLAN that is untagged by the switch as it crosses a trunk link. Which command should be used?
Admin asked 9 months ago • 
21 views0 answers0 votes
What are two benefits of using the PortFast feature? (Choose two.)
Admin asked 9 months ago • 
18 views0 answers0 votes
An engineer requires a switch interface to actively attempt to establish a trunk link with a neighbor switch. What command must be configured?
Admin asked 9 months ago • 
31 views0 answers0 votes
What is the benefit of configuring PortFast on an interface?
Admin asked 9 months ago • 
15 views0 answers0 votes
Refer to the exhibit. After the election process, what is the root bridge in the HQ LAN? Switch 1: 0C:E0:38:81:32:58 – Switch 2: 0C:0E:15:22:1A:61 – Switch 3: 0C:0E:15:1D:3C:9A – Switch 4: 0C:E0:19:A1:4D:16 –
Admin asked 9 months ago • 
16 views0 answers0 votes
DRAG DROP – Drag and drop the functions of AAA supporting protocols from the left onto the protocols on the right. Select and Place:
Admin asked 9 months ago • 
25 views0 answers0 votes
An engineer must establish a trunk link between two switches. The neighboring switch is set to trunk or desirable mode. What action should be taken?
Admin asked 9 months ago • 
12 views0 answers0 votes
Why does a switch flood a frame to all ports?
Admin asked 9 months ago • 
16 views0 answers0 votes
Which spanning-tree enhancement avoids the learning and listening states and immediately places ports in the forwarding state?
Admin asked 9 months ago • 
22 views0 answers0 votes
An engineer configures interface Gi1/0 on the company PE router to connect to an ISP. Neighbor discovery is disabled. Which action is necessary to complete the configuration if the ISP uses third-party network devices?
Admin asked 9 months ago • 
17 views0 answers0 votes
« Previous1…5556575859…70Next »

Other exams

No Result
View All Result

Welcome Back!

Login to your account below

Forgotten Password? Sign Up

Create New Account!

Fill the forms below to register

All fields are required. Log In

Retrieve your password

Please enter your username or email address to reset your password.

Log In