350-501 Mock Test Free – 50 Realistic Questions to Prepare with Confidence.
Getting ready for your 350-501 certification exam? Start your preparation the smart way with our 350-501 Mock Test Free – a carefully crafted set of 50 realistic, exam-style questions to help you practice effectively and boost your confidence.
Using a mock test free for 350-501 exam is one of the best ways to:
- Familiarize yourself with the actual exam format and question style
- Identify areas where you need more review
- Strengthen your time management and test-taking strategy
Below, you will find 50 free questions from our 350-501 Mock Test Free resource. These questions are structured to reflect the real exam’s difficulty and content areas, helping you assess your readiness accurately.
Which two IS-IS parameters must match before two Level 2 peers can form an adjacency? (Choose two.)A. hello timer setting
B. authentication settings
C. area ID
D. system ID
E. MTU
Refer to the exhibit. A network engineer must implement SNMPv3 on a Cisco IOS XR router running BGP. The engineer configures SNMPv3 to use SHA for authentication and AES for privacy on the routers, which are in a different data center in the same exchange as other routers. The engineer must also verify the associated MIB view family name, storage type, and status. Which set of actions meets these requirements?A. Add configuration snmp-server user UserJustMe GrpMonitoring v3 auth sha AuthPass1 priv 3des 128 PrivPass2 and use show snmp interface to verify the configuration.
B. Add configuration snmp-server user AuthUser group2 remote 10.1.1.1 v3 auth sha and use show snmp mib to verify the configuration.
C. Add configuration snmp-server user AuthUser group2 remote 10.1.1.1 v3 auth sha and use show snmp engineid to verify the configuration.
D. Add configuration snmp-server user UserJustMe GrpMonitoring v3 auth sha AuthPass1 priv aes 128 PrivPass2 and use show snmp view to verify the configuration.
Refer to the exhibit. A network engineer is implementing a standard customer route-policy on router ASBR1 with these requirements:
✑ It must accept only customer-assigned prefixes.
✑ It must preserve customer-advertised BGP communities.
✑ It must set the local-preference to 110 for all prefixes.
It must attach the ORIGINATION-PE and LOCAL-CITY communities to all accepted prefixes.
Which route policy must the engineer implement on ASBR1 to satisfy the requirements?
A.
B.
C.
D.
Refer to the exhibit. The radio network and packet core are using the route RX-RZ-RB to establish communication. The LDP session between 10.10.10.5 and 10.10.10.1 is experiencing link flapping at random intervals for 30-45 seconds each time. A network engineer must protect the LDP session and improve MPLS traffic convergence. Which action meets these requirements?A. Configure peer_acl_2 on RX and allow IP address 10.10.10.6 in LDP.
B. Attach peer_acl_1 in for session protection duration 1 on RX.
C. Add session protection duration 60 for peer_acl_1 under the MPLS LDP instance on RZ.
D. Enable IGP-LDP sync on RZ and RX.
DRAG DROP -
Drag and drop the methods of Cisco MPLS TE tunnel traffic assignment from the left onto their characteristics on the right.
Select and Place:
A new PE router is configured to run OSPF as an IGP with LDP on all interfaces. The engineer is trying to prevent black holes after convergence when the
PERSON device loses an LDP session with other PE routers. Which action must the engineer take to implement LDP session protection on a new PE router?A. Configure the mpls ldp session protection and mpls label protocol ldp commands on the interfaces on the new PE router that connect to the CENTER routers.
B. Configure the mpls ldp discovery targeted-hello accept and mpls ldp session protection commands on the interfaces on the new PE router that connect to the CE routers.
C. Configure the new PE router with the mpls ldp session protection command and on neighboring routers that connect to this new PE router.
D. Configure the new PE router with the mpls ldp session protection command on interfaces with directly connected neighbors.
Refer to the exhibit. While troubleshooting a connectivity issue on router R2, a network engineer with an employee id: 1234:44:876 notices that although it detects three OSPF links from R1, the OSPF prefixes are missing from the routing table. What is the reason for the problem?A. The serial interfaces have different MTUs
B. Both loopback interfaces on R1 are configured as stub
C. The subnet masks on the serial interfaces are mismatched
D. The R2 Serial1/0 interface is configured with an IP address, but the R1 Serial1/0 interface is unnumbered
Refer to the exhibit. An engineer is implementing BGP selective prefix suppression. The router must advertise only 10.16.4.0/24, 10.16.5.0/24, and summarized route 10.16.0.0/21, and suppress 10.16.6.0/24. Which configuration must the engineer apply to the router?A. Router (config)# router bgp 300 Router(config-router)# aggregate-address 10.16.6.0 255.255.252.0 as-set suppress-map SuppressMap
B. Router (config)# router bgp 300 Router(config-router)# aggregate-address 10.16.0.0 255.255.255.0 as-set suppress-map unSuppressMap
C. Router (config)# router bgp 300 Router(config-router)# aggregate-address 10.16.0.0 255.255.248.0 as-set suppress-map SuppressMap
D. Router (config)# router bgp 300 Router(config-router)# aggregate-address 10.16.6.0 255.255.255.0 as-set suppress-map SuppressMap
Refer to the exhibit A user is performing QoS marking on internet traffic and sending it with IPv4 and IPv6 headers on the provider edge device PE1. IPv4 traffic is classified with DSCP 4 and IPv6 traffic is classified with DSCP 6. Which action must the engineer take to begin implementing a QoS configuration on PE1 for the
IPv6 traffic?A. Create an access list that includes any IPv6 traffic and apply it to CM-20.
B. Create access list IPv6-match and configure match ip dscp 4 and match ip dscp 6 in class maps CM-10 and CM-20.
C. Configure match ip dscp 4 in class map CM-10 and match ip dscp 6 in class map CM-20.
D. Create access list IPv6-filter and remove DSCP value 4 and 6 in class maps CM-10 and CM-20.
What is the purpose of RSVP tear messages?A. to inform the headend router of LSP issues
B. to confirm successful end-to-end resource allocation
C. to reuse router resources for other reservation requests
D. to notify the tail-end router of resource unavailability on the transit router
Refer to the exhibit. An engineer ran this show telemetry command to view subscription SUB11 on RouterX. The engineer then decided that RouterY should provide the same output for sensor group SGroup13 as RouterX. The engineer cannot access RouterX to copy its configuration No access lists on the router block user access. Which configuration must the engineer apply on RouterY to provide the same output from the show telemetry command?A. RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# subscription SGroup13RouterY(config-model-driven-subs)# sensor-group-id SGroup13 sample-interval 20000
B. RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# sensor-group SGroup13RouterY(config-model-driven-snsr-grp)# sensor-path openconfig-interfaces:interfaces/interface
C. RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# destination-group SUB11RouterY(config-model-driven-dest)# address family ipv4 172.16.10.1 port 22471RouterY(config-model-driven-dest-addr)# encoding self-describing-gpbRouterY(config-model-driven-dest-addr)# protocol tcp
D. RouterY(config)# telemetry model-drivenRouterY(config-model-driven)# subscription SUB11RouterY(config-model-driven-subs)# sensor-group-id SGroup13 sample-interval 20000RouterY(config-model-driven-subs)# destination-id DGroup1
After a series of unexpected device failures on the network, a Cisco engineer is deploying NSF on the network devices so that packets continue to be forwarded during switchovers. The network devices reside in the same building, but they are physically separated into two different data centers. Which task must the engineer perform as part of the deployment?A. Implement an L2VPN with the failover peer to share state information between the active and standby devices.
B. Implement OSPF to maintain the link-state database during failover.
C. Implement VRFs and specify the forwarding instances that must remain active during failover.
D. Implement Cisco Express Forwarding to provide forwarding during failover.
Refer to the exhibit. Which statement about the status of the neighbor relationship between R1 and R2 is true?A. The neighbor relationship is down because the two routers are configured with different area types.
B. The neighbor relationship is down because the two routers are in the same subnet.
C. The neighbor relationship is up because R2 is level 1 and Ievel 2 router.
D. The neighbor relationship is down because R2 is operating as a Level 1 router and the two routers are in different areas.
A network architect plans to implement MPLS OAM to provide additional troubleshooting functionality for the NOC team. After analyzing the configuration on the
MPLS P/PE nodes, the architect decides to revise the CoPP policies. Which two actions ensure that the new solution is secure? (Choose two.)A. Allow port 3505 in the outbound direction only.
B. Allow the ICMP protocol only.
C. Allow the TCP and UDP protocols.
D. Allow the UDP protocol only.
E. Allow port 3503 in the inbound direction only.
Refer to the exhibit. The operations team is implementing an LDP-based configuration in the service provider core network with these requirements:
✑ R1 must establish LDP peering with the loopback IP address as its Router-ID.
✑ Session protection must be enabled on R2.
How must the team update the network configuration to successfully enable LDP peering between R1 and R2?A. Change the LDP password on R2 to Cisco.
B. Configure mpls ldp router-id loopback0 on R1 and R2.
C. Configure LDP session protection on R1.
D. Change the discover hello hold time and interval to their default values.
DRAG DROP -
Drag and drop the BGP Best Path Algorithm rules from the left into the corresponding order of importance on the right.
Select and Place:
After implementing MPLS protocol for multiple VRFs on a single Cisco device, the engineer notices all VRFs on the router still do not have the LDP session protection feature enabled. Which configuration must the engineer apply to enable the LDP session protection feature for LDP neighbors within each VRF?A. Configure LDP session protection globally on the device only.
B. Configure LDP session protection within the individual VRFs.
C. Configure LDP session authentication on the device to enable LDP session protection on each VRF automatically.
D. Configure LDP session protection globally on the device and on each neighbor that requires session protection.
An engineer is developing a configuration script to enable dial-out telemetry streams using gRPC on several new devices. TLS must be disabled on the devices.
Which configuration must the engineer apply on the network?A. telemetry model-driven destination-group ciscotest address-family ipv4 192.168.1.0 port 57500 encoding self-describing-gpb protocol grpc tls-hostname ciscotest.com commit
B. telemetry model-driven destination-group DGroup1 address-family ipv4 172.0.0.0 port 5432 encoding self-describing-gpb protocol tcp commit
C. telemetry model-driven destination-group ciscotest address-family ipv4 192.168.1.0 port 57500 encoding self-describing-gpb protocol grpc no-tls commit
D. telemetry model-driven destination-group ciscotest address-family ipv4 192.168.1.0 port 57500 encoding self-describing-gpb protocol grpc commit
Refer to the exhibit. Router R1 is reporting that its BGP neighbor adjacency to router R2 is down, but its state is Active. Which configuration must be applied to routers R1 and R2 to fix the problem?A. R1 router bgp 5400 neighbor 11.11.11.11 remote-as 5400 neighbor 11.11.11.11 update-source Loopback0 R2 router bgp 5400 neighbor 11.11.11.12 remote-as 5400 neighbor 11.11.11.12 update-source Loopback0
B. R1 router bgp 5400 neighbor 2.2.2.2 remote-as 5400 neighbor 2.2.2.2 update-source Loopback0 R2 router bgp 5400 neighbor 1.1.1.1 remote-as 5400 neighbor 1.1.1.1 update-source Loopback0
C. R1 router bgp 5400 neighbor 2.2.2.2 remote-as 5400 R2 router bgp 5400 neighbor 1.1.1.1 remote-as 5400
D. R1 router bgp 5400 neighbor 1.1.1.1 remote-as 5400 neighbor 1.1.1.1 update-source Loopback0 R2 router bgp 5400 neighbor 2.2.2.2 remote-as 5400 neighbor 2.2.2.2 update-source Loopback0
Refer to the exhibit. Based on the show command output, which result is true after BGP session is established?A. The IOS XR router advertises and accepts all routes to and from eBGP neighbor 192.168.2.2.
B. The IOS XR router advertises all routes to the neighbor 192.168.2.2, but it does not accept any routes from 192.168.2.2.
C. No routes are accepted from the neighbor 192.168.2.2, nor are any routes advertised to it.
D. The IOS XR router does not advertises any routes to the neighbor 192.168.2.2, but it accepts any routes from 192.168.2.2.
Refer to the exhibit. An engineer has started to configure a router for secure remote access as shown. All users who require network access need to be authenticated by the SSH protocol. Which two actions must the engineer implement to complete the SSH configuration? (Choose two.)A. Configure an IP domain name.
B. Configure ACL 100 to permit access to port 22.
C. Configure a password under the vty lines.
D. Configure crypto keys.
E. Configure service password encryption.
Refer to the exhibit. A Cisco engineer is implementing gRPC dial-out on an ASR. Receiver 192.168.1.1 will be assigned one of the subscriptions, and it will manage the ASR. Which command is needed to complete the router configuration?A. protocol tcp
B. protocol any
C. protocol grpc
D. protocol all
Refer to the exhibit. Routers R1 and R2 are connected via a serial link and use the IS-IS routing protocol for route exchange. After a configuration change on R2, IS-IS connectivity is interrupted. A network engineer confirmed that the interfaces are in the UP state and connectivity exists between the two routers. Which two actions must the engineer perform to resolve the problem? (Choose two.)A. Change the hello interface timer to 10 seconds on R1
B. Change the MTU to 1500 bytes on R2
C. Change R2 to an IS-IS Level 1 router
D. Disable padding for hello packets under the serial interface on R2
E. Enable hello packet padding globally on R1
A network engineer is configuring RIP as the routing protocol between multiple PEs and CEs. The engineer must avoid advertising the same routes back to their sources. Which action should be performed on the routers to accomplish this task?A. Define the site of origin on each interface.
B. Configure a different route distinguisher for each prefix.
C. Define VRFs on each device to separate the traffic.
D. Enable bidirectional forwarding detection on each device.
DRAG DROP -
Drag and drop the descriptions from the left onto the corresponding OS types on the right.
Select and Place:
Refer to the exhibit. An engineer is securing a customer's network. Which command must the engineer use to complete this configuration to prevent a DoS attack?A. neighbor ttl-security
B. ebgp-multihop
C. neighbor ebgp-multihop
D. ttl-security
A network operator with an employee ID: 1516:11:567 must implement a PIM-SSM multicast configuration on the customer's network so that users in different domains are able to access and stream live traffic. The IGMP version must be enabled to support the SSM implementation. Which action must the engineer perform on R1 to complete the SSM implementation?A.
B.
C.
D.
Refer to the exhibit. When the Link Aggregation configuration router is running on Cisco IOS XR Software, which LACP interface configuration is needed to add the interface to the bundle?
A.
B.
C.
D.
The network team is planning to implement IPv6 on the company's existing IPv4 network infrastructure. The network currently uses IS-IS to share routes between peers. Which task must the team perform so that IS-IS will run in multitopology mode on the updated IPv6 network?A. Configure the links between the network routers as point-to-point.
B. Configure the network routers to use metric-style wide.
C. Configure the network routers as Level 2 routers.
D. Configure the IS-IS IPv6 metric on the dual-stack links.
Refer to the exhibit. An ISP provides shared VoIP Extranet services to a customer in VRF-100 with these settings:
✑ The VoIP services are hosted in the 198.19.100.0/24 space.
✑ The customer has been assigned the 198.18.1.0/29 IP address block.
✑ VRF-100 is assigned import and export route target 65010:100.
Which configuration must the engineer apply to PE-1 to provision VRF-100 and provide access to the shared services?A. vrf definition VRF-100 rd 172.17.255.1:100 ! address-family ipv4 export map VRF-100-EXPORT import map VRF-100-IMPORT exit-address-family ! route-map VRF-100-EXPORT permit 10 match ip address prefix-list VRF-100-ALLOWED-EXPORT set extcommunity rt 65010:100 65010:2999 route-map VRF-100-EXPORT permit 20 set extcommunity rt 65010:100 ! route-map VRF-100-IMPORT permit 10 match extcommunity VRF-100-RT SHARED-SERVICES ! ip extcommunity-list standard SHARED-SERVICES permit rt 65010:1999 ip extcommunity-list standard VRF-100-RT permit rt 65010:100 ip prefix-list VRF-100-ALLOWED-EXPORT seq 5 permit 198.18.1.0/29
B. vrf definition VRF-100 rd 172.17.255.1:100 ! address-family ipv4 export map VRF-100-EXPORT route-target import 65010:100 route-target import 65010:2999 exit-address-family ! route-map VRF-100-EXPORT permit 10 match ip address prefix-list VRF-100-ALLOWED-EXPORT set extcommunity rt 65010:100 65010:1999 route-map VRF-100-EXPORT permit 20 set extcommunity rt 65010:100 ! ip prefix-list VRF-100-ALLOWED-EXPORT seq 5 permit 198.18.1.0/29
C. vrf definition VRF-100 rd 172.17.255.1:100 ! address-family ipv4 export map VRF-100-EXPORT route-target import 65010:100 route-target import 65010:1999 exit address-family ! route-map VRF-100-EXPORT permit 10 match ip address prefix-list VRF-100-ALLOWED-EXPORT set extcommunity rt 65010:100 65010:2999 route-map VRF-100-EXPORT permit 20 set extcommunity r 65010:100 ! ip prefix-list VRF-100-ALLOWED-EXPORT seq 5 permit 198.18.1.0/29
D. vrf definition VRF-100 rd 172.17.255.1:100 ! address-family ipv4 route-target export 65010:100 route-target export 65010:1999 route-target import 65010:100 route-target import 65010:2999 exit-address-family
DRAG DROP -
Drag and drop the technologies from the left onto the correct definitions on the right.
Select and Place:
Which programmable API allows the service provider to plan and optimize the automation of network operations and achieve dosed-loop operations?A. Network Services Orchestrator
B. WAN Automation Engine
C. Crosswork Network Automation
D. Evolved Programmable Network Manager
DRAG DROP -
Drag and drop the functionalities from the left onto the correct target fields on the right.
Select and Place:
How does SR policy operate in Segment Routing Traffic Engineering?A. An SR policy for color and endpoint is deactivated at the headend as soon as the headend learns a valid candidate path for the policy.
B. When "invalidation drop" behavior occurs, the SR policy forwarding entry is removed and the router drops all traffic that is steered into the SR policy.
C. When a set of SID lists is associated with the SR policy designated path, traffic steering is ECMP-based according to the qualified cost of each SID-list.
D. An active SR policy installs a BSID-keyed entry in the forwarding table to steer the packets that match the entry to the SR policy SID-list.
What Is one of the differences between Ansible and Chef?A. Ansible uses YAML and Chef uses Ruby.
B. Chef requires the use of Windows in the environment and Ansible requires Linux.
C. Chef is highly scalable and Ansible is highly secure.
D. Ansible uses Ruby and Chef uses Python.
What are two features of 6RD IPv6 transition mechanism? (Choose two.)A. It inserts IPv4 bits into an IPv6 delegated prefix.
B. It uses a native IPv6-routed network between CE routers and the BR router.
C. It allows dynamic 1:N translation of IPv6 address.
D. It uses stateful automatic 6to4 tunnels between CE routers and the BR router.
E. It uses stateless automatic 6to4 tunnels between CE routers and the BR router.
Which task must be performed first to implement BFD in an IS-IS environment?A. Configure BFD in an interface configuration mode.
B. Disable Cisco Express Forwarding on all interfaces running routing protocols other than IS-IS.
C. Configure all IS-IS routers as Level 2 devices.
D. Configure BFD under the IS-IS process.
Refer to the exhibit. This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?A. It shows that the full configuration is being modeled by YANG.
B. It shows NETCONF uses remote procedure calls.
C. It shows the hostname of the device as rpc-reply.
D. It shows that the running configuration is blank.
Refer to the exhibit. Export statistics received do not include the BGP next hop.
Which statement about the NetFlow export statistics is true?A. Loopback 0 must be participating in BGP for it to be included in the export statistics.
B. To include the BGP next hop in the export statistics, those keywords must be included with the version 9 entry.
C. The origin AS and the peer-as will be included in the export statistics.
D. Only the origin AS of the source router will be included in the export statistics.
Refer to the exhibit. The network engineer who manages ASN 65001 is troubleshooting suboptimal routing to the 198.18.15.0/24 prefix. According to the network requirements:
✑ Routing to IP destinations in the 198.18.15.0/25 block must be preferred via the EDGE-1 PE.
✑ Routing to IP destinations in the 198.18.15.128/25 block must be preferred via the EDGE-2 PE.
✑ More specific prefixes of the 198.18.15.0/24 block must not be advertised beyond the boundaries of ASN 64611.
✑ Routing to 198.18.15.0/24 must be redundant in case one of the uplinks on INT-R1 fails.
Which configuration must the network engineer implement on INT-R1 to correct the suboptimal routing and fix the issue?A. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (no-export, peeras:65001) done endif if destination in (198.18.15.0/24) then prepend as-path 65001 3 done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT out end
B. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (internal, peeras:65001) done endif if destination in (198.18.15.0/24) then done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT out end
C. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (no-advertise, peeras:65001) done endif if destination in (198.18.15.128/25) then prepend as-path 65001 3 done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT out end
D. configure terminal route-policy ASN65001-SPECIFIC-OUT if destination in (198.18.15.0/25) then set community (no-export, peeras:65001) done endif if destination in (198.18.15.128/25) then prepend as-path 65001 3 done endif drop end-policy ! router bgp 65001 neighbor 100.65.0.1 address-family ipv4 unicast route-policy ASN65001-SPECIFIC-OUT in end
Refer to the exhibit. Users in AS 65010 are connected with the application server in AS 65050 with these requirements:
AS 65010 users are experiencing latency and congestion to connect with application server 172.16.50.10.
✑ AS 65030 must be restricted to become Transient Autonomous System for traffic flow.
✑ Links connected to AS 65020 and AS 65040 are underutilized and must be used efficiently for traffic.
Which two configurations must be implemented to meet these requirements? (Choose two.)A. Apply the AS-Path route-map policy for traffic received from R3.
B. Configure the route map to prepend the AS-Path attribute for R5-R3 BGP peering.
C. Apply the MED route-map policy for traffic received from R4.
D. Configure a higher Local preference for R5-R4 BGP peering.
E. Configure the route map to set the MED 50 attribute for R5-R4 BGP peering.
What are two factors to consider when implementing NSR High Availability on an MPLS PE router? (Choose two.)A. It requires all PE-CE sessions to support NSR
B. It requires routing protocol extensions
C. It consumes more memory and CPU resources than NSF
D. It operates normally without NSR support on the PE peers
E. It cannot sync state information across redundant RPs
Refer to the exhibit. Which statement supports QPPB implementation?A. QPPB policies affect only egress traffic.
B. QoS policies rely exclusively on BGP attributes to manipulate traffic.
C. QoS policies are identified in the MPLS forwarding table.
D. QoS policies use BGP to gain full coverage on the network.
Refer to the exhibit. Tier 1 ISP A purchased several Tier 2 ISPs to increase their customer base and provide more regional coverage. ISP A plans to implement MPLS services in the access layer, with scalability up to 100,000 devices in one packet network and service recovery up to 50 ms. The network architect decided to use different independent IGP and LDP domains and interconnect LSPs that are based on RFC 3107. Which two actions must the network engineer perform to meet the requirements? (Choose two.)A. Implement BGP inline RR functionality with next-hop-self capabilities on routers R2 and R3.
B. Implement the IS-IS routing protocol on the access domain.
C. Implement BGP connectivity between routers R1 and R4 with VPNv4 address family enabled.
D. Configure three OSPF areas, with Area 0 in the core domain, and Areas 2 and 3 in the aggregation domain.
E. Implement BGP PIC core functionality on routers R2 and R3.
Refer to the exhibit. The service provider is serving hosts with two different multicast streams from source X and source Y. Source X is multicast group 224.0.0.0/8, and source Y is multicast group 226.0.0.0/8. Multicast source X should send its stream through bidirectional RP address 10.20.1.1, and multicast source Y should send its stream through RP address 10.20.2.1. Which configuration meets these requirements?A. Enable ip pim ssm default on RA and RB.
B. Add ip pim bidir-enable in global mode on RB.
C. Permit the source X and source Y IP addresses in the access list on RB.
D. Set PIM sparse mode with a static RP address of 10.20.2.1 on RA and RC.
Refer to the exhibit. BGPsec is implemented on R1, R2, R3, and R4. BGP peering is established between neighboring autonomous systems.
Which statement about implementation is true?A. BGP updates from the iBGP peers are appended with a community of local-as.
B. BGP updates from the all BGP peers are appended with a community of no-export.
C. BGP updates from the eBGP peers are appended with an additional AS path value that is statically set by the domain administrator.
D. BGP updates from the eBGP peers are appended with a BGPsec attribute sequence that includes a public key hash and digital signature.
Refer to the exhibit. A network engineer at a large ISP Is configuring telemetry streams to monitor the health status of PE routers on the network using gRPC dial-out. The PE routers are located at several data centers in different physical locations, and they are using IS-IS and BGP for routing. Which additional configuration must the engineer implement on the PE routers to meet the goal?A.
B.
C.
D.
Refer to the exhibit. An engineer is configuring router R1 for OSPFv3 as shown. Which additional configuration must be performed so that the three active interfaces on the router will advertise routes and participate in OSPF IPv6 processes?
A.
B.
C.
D.
Refer to the exhibit. A host connected to R3 must connect with a server on R1 that provides critical, time-sensitive data. Traffic between the host and server must always be given bandwidth to traverse the links when they are congested, with other traffic being dropped. How must the network engineer implement a QoS strategy with classification to ensure that the traffic is given the appropriate bandwidth?A. Implement policing to rate-limit noncritical traffic that exceeds designated thresholds.
B. Implement traffic shaping to delay noncritical traffic when the link is congested.
C. Implement strict priority to guarantee bandwidth for the server traffic.
D. Implement FIFO to guarantee that the server traffic is sent first while other traffic is queued.
Which configuration mode do you use to apply the mpls ldp graceful-restart command in IOS XE Software?A. MPLS LDP neighbor
B. interface
C. MPLS
D. global
Access Full 350-501 Mock Test Free
Want a full-length mock test experience? Click here to unlock the complete 350-501 Mock Test Free set and get access to hundreds of additional practice questions covering all key topics.
We regularly update our question sets to stay aligned with the latest exam objectives—so check back often for fresh content!
Start practicing with our 350-501 mock test free today—and take a major step toward exam success!