You are a network operator troubleshooting BGP connectivity.
Which two statements are correct about the output shown in the exhibit? (Choose two.)

A. Peer 10.32.1.2 is configured for AS 63645.

B. The BGP session is not established.

C. The R1 is configured for AS 65400.

D. The routers are exchanging IPv4 routes.

You have configured a GRE tunnel. To reduce the risk of dropping traffic, you have configured a keepalive OAM probe to monitor the state of the tunnel; however, traffic drops are still occurring.
Referring to the exhibit, what is the problem?

A. For GRE tunnels, the OAM protocol requires that the BFD protocols also be used.

B. The “event link-adjacency-loss” option must be set

C. LLDP needs to be removed from the gr-1/1/10.1 interface.

D. The hold time value must be two times the keepalive-time value

You are receiving the BGP route shown in the exhibit from four different upstream ISPs.
Referring to the exhibit, which ISP will be selected as the active path?

A. ISP 1

B. ISP 3

C. ISP 4

D. ISP 2

Referring to the exhibit, which router will become the OSPF BDR if all routers are powered on at the same time?

A. R4

B. R1

C. R3

D. R2

Which two statements are correct about tunnels? (Choose two.)

A. BFD cannot be used to monitor tunnels.

B. Tunnel endpoints must have a valid route to the remote tunnel endpoint.

C. IP-IP tunnels are stateful.

D. Tunnels add additional overhead to packet size.

An update to your organization's network security requirements document requires management traffic to be isolated in a non-default routing-instance. You want to implement this requirement on your Junos-based devices.
Which two commands enable this behavior? (Choose two.)

A. set routing-instances mgmt_junos interface ge-0/0/0

B. set routing-instances mgmt_junos interface em1

C. set system management-instance

D. set routing-instances mgmt_junos

Referring to the exhibit, which statement is correct?

A. The local device is using a bridge priority of 4k.

B. The root bridge is using a bridge priority of 4k.

C. The root bridge has not been elected for this RSTP topology

D. The local device is the root bridge for this RSTP topology.

Which statement is correct about graceful Routing Engine switchover (GRES)?

A. The PFE restarts and the kernel and interface information is lost.

B. GRES has a helper mode and are starting mode.

C. When combined with NSR, routing is preserved and the new master RE does not restart rpd.

D. With no other high availability features enabled, routing is preserved and the new master RE does not restart rpd.

In RSTP, which three port roles are associated with the discarding state? (Choose three.)

A. root

B. backup

C. alternate

D. disabled

E. designated

You have DHCP snooping enabled but no entries are automatically created in the snooping database for an interface on your EX Series switch.
What are two reasons for the problem? (Choose two.)

A. The device that is connected to the interface has performed a DHCPRELEASE.

B. MAC limiting is enabled on the interface.

C. The device that is connected to the interface has a static IP address.

D. Dynamic ARP inspection is enabled on the interface.

What is the maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation?

A. 1496 bytes

B. 1480 bytes

C. 1500 bytes

D. 1476 bytes

You are asked to connect an IP phone and a user computer using the same interface on an EX Series switch. The traffic from the computer does not use a VLAN tag, whereas the traffic from the IP phone uses a VLAN tag.
Which feature enables the interface to receive both types of traffic?

A. native VLAN

B. DHCP snooping

C. MAC limiting

D. voice VLAN

You are troubleshooting an issue where traffic to 192.168.10.0/24 is being sent to R1 instead of your desired path through R2.
Referring to the exhibit, what is the reason for the problem?

A. R2’s route is not the best path due to loop prevention.

B. R2’s route is not the best path due to a lower origin code.

C. R1’s route is the best path due to a higher local preference.

D. R1’s route is the best path due to the shorter AS path.

Which statement is correct about the storm control feature?

A. The storm control feature is enabled in the factory-default configuration on EX Series switches.

B. The storm control feature requires a special license on EX Series switches.

C. The storm control feature is not supported on aggregate Ethernet interfaces.

D. The storm control configuration only applies to traffic being sent between the forwarding and control plane.

You want to enable redundancy for the EBGP peering between the two routers shown in the exhibit.
Which three actions will you perform in this scenario? (Choose three.)

A. Configure BGP multihop.

B. Configure loopback interface peering.

C. Configure routes for the peer loopback interface IP addresses.

D. Configure an MD5 peer authentication.

E. Configure a cluster ID.

You are receiving multiple BGP routes from an upstream neighbor and only want to advertise a single summarized prefix to your internal OSPF neighbors. This route should only be advertised when you are receiving these BGP routes from this neighbor.
In this scenario, which type of route should you create?

A. aggregate route

B. static route using the resolve feature

C. generate route

D. static route using qualified next hops

Which two events cause a router to advertise a connected network to OSPF neighbors? (Choose two.)

A. When an OSPF adjacency is established.

B. When an interface has the OSPF passive option enabled.

C. When a static route to the 224.0.0.6 address is created.

D. When a static route to the 224.0.0.5 address is created.

You want to verify prefix information being sent from 10.36.1.4.
Which two statements are correct about the output shown in the exhibit? (Choose two.)

A. The routes displayed have traversed one or more autonomous systems.

B. The output shows routes that were received prior to the application of any BGP import policies.

C. The output shows routes that are active and rejected by an import policy.

D. The routes displayed are being learned from an IBGP peer.

Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)

A. Redundant trunk groups load-balance traffic across two designated uplink interfaces.

B. If the active link fails, then the secondary link automatically takes over.

C. Layer 2 control traffic is permitted on the secondary link.

D. Redundant trunk groups must be connected to the same aggregation switch.

An update to your organization's network security requirements document requires management traffic to be isolated in a non-default routing-instance. You want to implement this requirement on your Junos-based devices.
Which two commands enable this behavior? (Choose two.)

A. set routing-instances mgmt_junos interface ge-0/0/0

B. set routing-instances mgmt_junos interface em1

C. set system management-instance

D. set routing-instances mgmt_junos

You have configured the four EX Series switches with RSTP, as shown in the exhibit. You discover that whenever a link between switches goes up or down, the switches take longer than expected for RSTP to converge, using the default settings.
In this scenario, which action would solve the delay in RSTP convergence?

A. The hello-time must be increased.

B. The force-version must be removed.

C. The bridge priority for EX-4 must be set at 4000.

D. The max-age must be increased to 20.

You have two OSPF routers forming an adjacency. R1 has a priority of 32 and a router ID of 192.168.1.2. R2 has a priority of 64 and a router ID of 192.168.1.1. The routers were started at the same time and all other OSPF settings are the default settings.
Which statement is correct in this scenario?

A. At least three routers are required for a DR/BDR election.

B. Router IDs must match for an adjacency to form.

C. R2 will be the BDR.

D. R1 will be the BDR.

Which statement about aggregate routes is correct?

A. Aggregate routes can only be used for static routing but not for dynamic routing protocols.

B. Aggregate routes are automatically generated for all of the subnets in a routing table.

C. Aggregate routes are always preferred over more specific routes, even when the specific routes have a better path.

D. Aggregate routes are used for advertising summarized network prefixes.

Which two mechanisms are part of building and maintaining a Layer 2 bridge table? (Choose two.)

A. blocking

B. flooding

C. learning

D. listening

Which two statements correctly describe RSTP port roles? (Choose two.)

A. The designated port forwards data to the downstream network segment or device.

B. The backup port is used as a backup for the root port.

C. The alternate port is a standby port for an edge port.

D. The root port is responsible for forwarding data to the root bridge.

Which two statements are true about the default VLAN on Juniper switches? (Choose two.)

A. The default VLAN is set to a VLAN ID of 1 by default

B. The default VLAN ID is not assigned to any interface.

C. The default VLAN ID is not visible.

D. The default VLAN ID can be changed.

Which statement is correct about the storm control feature?

A. The storm control feature is enabled in the factory-default configuration on EX Series switches.

B. The storm control feature requires a special license on EX Series switches.

C. The storm control feature is not supported on aggregate Ethernet interfaces.

D. The storm control configuration only applies to traffic being sent between the forwarding and control plane.

What is the default MAC age-out timer on an EX Series switch?

A. 30 minutes

B. 30 seconds

C. 300 minutes

D. 300 seconds

You have configured a GRE tunnel. To reduce the risk of dropping traffic, you have configured a keepalive OAM probe to monitor the state of the tunnel; however, traffic drops are still occurring.
Referring to the exhibit, what is the problem?

A. For GRE tunnels, the OAM protocol requires that the BFD protocols also be used.

B. The “event link-adjacency-loss” option must be set

C. LLDP needs to be removed from the gr-1/1/10.1 interface.

D. The hold time value must be two times the keepalive-time value

Which command displays the output shown in the exhibit?

A. show route forwarding-table

B. show ethernet-switching table

C. show ethernet-switching table extensive

D. show route forwarding-table family ethernet-switching

You want to use filter-based forwarding (FBF) on your Internet peering router to load-balance traffic to two directly connected ISPs based on the source address.
Which two statements are correct in this scenario? (Choose two.)

A. FBF uses the no-forwarding routing instance type.

B. FBF uses the forwarding routing instance type.

C. RIB groups are used to copy routes from the inet.0 routing table.

D. RIB groups are used to hide routes in the inet.0 routing table.

Which two statements are correct about using firewall filters on EX Series switches? (Choose two.)

A. You can deploy only stateless firewall filters on an EX Series switch.

B. You can only apply firewall filters to Layer 2 traffic on an EX Series switch.

C. You can apply firewall filters to both Layer 2 and Layer 3 traffic on an EX Series switch.

D. You can deploy both stateless and stateful firewall filters on an EX Series switch.

The ISP1.inet.0 route table has currently no routes in it.
What will happen when you commit the configuration shown on the exhibit?

A. The inet.0 route table will be completely overwritten by the ISP1.inet.0 route table.

B. The inet.0 route table will be imported into the ISP1.inet.0 route table.

C. The ISP1.inet.0 route table will be completely overwritten by the inet.0 route table.

D. The ISP1.inet.0 route table will be imported into the inet.0 route table.

Which two mechanisms are part of building and maintaining a Layer 2 bridge table? (Choose two.)

A. blocking

B. flooding

C. learning

D. listening

Which two statements are correct about generated routes? (Choose two.)

A. Generated routes require a contributing route.

B. Generated routes show a next hop in the routing table.

C. Generated routes appear in the routing table as static routes.

D. Generated routes cannot be redistributed into dynamic routing protocols.

Which two statements about BGP facilitate the prevention of routing loops between two autonomous systems? (Choose two.)

A. EBGP routers will append their AS number when advertising routes to their neighbors.

B. EBGP routers will only accept routes that contain their own AS number in the AS_PATH.

C. EBGP routers will drop routes that contain their own AS number in the AS_PATH.

D. EBGP routers will prepend their AS number when advertising routes to their neighbors.

Two routers share the same highest priority and start time.
In this situation, what is evaluated next when determining the designated router?

A. The router with the lowest router ID become the DR.

B. The router with the highest router ID becomes the DR.

C. The routers perform another DR election.

D. The router with the highest MAC address become the DR.

What is a purpose of using a spanning tree protocol?

A. to look up MAC addresses

B. to eliminate broadcast storms

C. to route IP packets

D. to tunnel Ethernet frames

In RSTP, which three port roles are associated with the discarding state? (Choose three.)

A. root

B. backup

C. alternate

D. disabled

E. designated

What is the default MAC age-out timer on an EX Series switch?

A. 30 minutes

B. 30 seconds

C. 300 minutes

D. 300 seconds

What are two characteristics of RSTP alternate ports? (Choose two.)

A. RSTP alternate ports block traffic while receiving superior BPDUs from a neighboring switch.

B. RSTP alternate ports provide an alternate lower cost path to the root bridge.

C. RSTP alternate ports provide an alternate higher cost path to the root bridge.

D. RSTP alternate ports are active ports used to forward frames toward the root bridge.

Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)

A. Redundant trunk groups use spanning tree to provide loop-free redundant uplinks.

B. Redundant trunk groups load balance traffic across two designated uplink interfaces.

C. Layer 2 control traffic is permitted on the secondary link.

D. If the active link fails, then the secondary link automatically takes over.

Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)

A. Redundant trunk groups use spanning tree to provide loop-free redundant uplinks.

B. Redundant trunk groups load balance traffic across two designated uplink interfaces.

C. Layer 2 control traffic is permitted on the secondary link.

D. If the active link fails, then the secondary link automatically takes over.

Which statement is correct about controlling the routes installed by a RIB group?

A. An import policy is applied to the RIB group.

B. Only routes in the last table are installed

C. A firewall filter must be configured to install routes in the RIB groups.

D. An export policy is applied to the RIB group.

You are troubleshooting a BGP routing issue between your network and a customer router and are reviewing the BGP routing policies.
Which two statements are correct in this scenario? (Choose two.)

A. Export policies are applied to routes in the RIB-In table.

B. Import policies are applied to routes in the RIB-Local table.

C. Import policies are applied after the RIB-In table.

D. Export policies are applied after the RIB-Local table.

You implemented the MAC address limit feature with the shutdown action on all interfaces on your switch.
In this scenario, which statement is correct when a violation occurs?

A. By default, you must manually clear the violation for the interface to send and receive traffic again.

B. By default, the violation will automatically be cleared after 300 seconds and the interface will resume sending and receiving traffic for all learned devices.

C. By default, devices that are learned before the violation occurs are still allowed to send and receive traffic through the specific interface.

D. By default, the interface will continue to send and receive traffic for all connected devices after a violation has occurred.

What does the * indicate in the output shown in the exhibit?

A. The switch ports have a router attached.

B. The interface is down.

C. The interface is active.

D. All interfaces have elected a root bridge.

Which two types of tunnels are able to be created on all Junos devices? (Choose two.)

A. STP

B. GRE

C. IP-IP

D. IPsec

Which command displays the output shown in the exhibit?

A. show route forwarding-table

B. show ethernet-switching table

C. show ethernet-switching table extensive

D. show route forwarding-table family ethernet-switching

You are concerned about spoofed MAC addresses on your LAN.
Which two Layer 2 security features should you enable to minimize this concern? (Choose two.)

A. dynamic ARP inspection

B. IP source guard

C. DHCP snooping

D. static ARP