What is a valid IPv6 address?

A. 00:05:85:23:45:67

B. 127.0.0.1

C. 2001:0db8:3000:2215:0000:0000:aaaa:1111

D. 49.0001.0192.0168.1001.00

Which statement is true about the routing table?

A. The routing table exists in the control plane only.

B. The routing table exists in the control plane and in the forwarding plane.

C. The routing table contains both active and inactive routes.

D. The routing table is stored on compact flash.

What are three characteristics of Layer 2 switches? (Choose three.)

A. Layer 2 switches forward broadcast traffic.

B. Layer 2 switches forward traffic addresses to hosts that reside on the same collision domain.

C. Layer 2 switches separate multicast domains.

D. Layer 2 switches separate collision domains.

E. Layer 2 switches forward traffic addressed to hosts that reside on a different collision domain.

Which routing table stores IPv4 unicast routes and is used by multicast routing protocols to prevent loops?

A. inet.0

B. inet.1

C. inet.2

D. inet.3

-- Exhibit --
user@router> restart
^
unknown command.
-- Exhibit --
You are investigating routing problems on a device running the Junos OS. You receive the error shown in the exhibit when you attempt to restart the routing process.
Which statement describes the problem?

A. You have typed an invalid command.

B. You must be in configuration mode to restart the routing process.

C. You do not have permission to restart the routing process.

D. You must wait until close of business to restart the routing process, based on user-defined policy.

-- Exhibit --
[edit interfaces ge-0/0/6]
user@router# show
unit 0 {
familyinet {
address 172.16.10.100/24;
address 172.16.10.101/24;
}
}
-- Exhibit --
You have two IP addresses configured on the ge-0/0/6 interface, as shown in the exhibit. You want to select the 172.16.10.101 address as the source address for packets sent from this interface to hosts on a remote subnet.
Which parameter would you add to the 172.16.10.101 address to complete this task?

A. preferred

B. broadcast

C. primary

D. arp 172.16.10.101

Which two commands may be used when configuring an IP address for a Gigabit Ethernet interface? (Choose two.)

A. set interfaces ge-0/0/0.0 address 10.1.1.1/24

B. set interfaces ge-0/0/0.0 family inet address 10.1.1.1/24

C. set interfaces ge-0/0/0 unit 0 family inet address 10.1.1.1/24

D. set interfaces ge-0/0/0 address 10.1.1.1/24

-- Exhibit --
[edit interfaces ge-0/0/1]
user@router# show
unit 100 {
vlan-id 100;
family inet {
address 10.1.1.1 /24;
}
}
[edit interfaces ge-0/0/1]
user@router# commit check
[edit interfaces ge-0/0/1]
'unit 100'
Only unit 0 is valid for this encapsulation
error: configuration check-out failed
-- Exhibit --
Referring to the exhibit, you are unable to commit the configuration for the ge-0/0/1 interface.
What must you do to commit the configuration?

A. You must set the vlan-tagging parameter under the [edit interfaces ge-0/0/1] hierarchy.

B. You must use the rename command to change unit 100 to unit 0.

C. You must set the encapsulation flexible-ethernet-services parameter under the [edit interfaces ge-0/0/1] hierarchy.

D. You must set the encapsulation vlan-ccc parameter under the [edit interfaces ge-0/0/1 unit 100] hierarchy.

What are two Junos processes? (Choose two.)

A. OSPF SPF daemon (ospfd)

B. SNMP daemon (snmpd)

C. BGP daemon (bgpd)

D. Routing protocols daemon (rpd)

What is the default action for firewall filters?

A. accept

B. reject

C. discard

D. log

How do you save the current candidate configuration in the set format to permanent storage media?

A. [edit] user@router# show | set | save /var/tmp/current.conf

B. [edit] user@router# show | compare set | save /var/tmp/current.conf

C. [edit] user@router# save /var/tmp/current.conf | display set

D. [edit]

-- Exhibit --
user@router> show route protocol static
inet.0: 15 destinations, 15 routes (15 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
99.0.0.0/17        *[Static/5] 00:00:11
>to 10.1.1.2 via ge-0/0/1.0
99.0.0.0/19        *[Static/5] 00:00:11
>to 10.1.2.2 via ge-0/0/2.0
99.0.0.0/24        *[Static/5] 00:00:11
>to 10.1.3.2 via ge-0/0/3.0
99.0.0.0/26        *[Static/5] 00:00:11
>to 10.1.4.2 via ge-0/0/4.0
-- Exhibit --
In the exhibit, there are four static routes that route traffic through different interfaces.
Which interface does the router use if traffic is sent to the 99.0.0.1 destination?

A. ge-0/0/1

B. ge-0/0/2

C. ge-0/0/3

D. ge-0/0/4

Which information would you find using the CLI help function? (Choose two.)

A. message of the day

B. tip of the day

C. explanation for specific system log error messages

D. explanation for specific traceoptions log messages

Which command is used to load the rescue configuration?

A. load override rescue

B. rollback rescue

C. load replace rescue-configuration

D. rollback 49

Which two statements are correct about the request system zeroize local command? (Choose two.)

A. The command removes all data files.

B. The command preserves the management interface addresses.

C. The command resets all key values.

D. The command removes all user-created files from the system.

Which two statements are true about TCP communication? (Choose two.)

A. The receiver acknowledges the final packet in each communications stream.

B. The receiver adds sequencing numbers to the packets received.

C. The sender adds sequencing numbers to the packets it sends.

D. The receiver acknowledges each packet it receives from the sending device.

Random early detection (RED) is associated with which class of service component?

A. classification

B. policing

C. queuing

D. scheduling

What is the central processing component of the forwarding plane?

A. PFE

B. RE

C. Junos OS

D. forwarding table

What is a valid option when using the ping command?

A. packet loss

B. packet size

C. CRC

D. TCP port

Which command prompt indicates that you are in operational mode?

A. user@router&

B. user@router#

C. user@router%

D. user@router>

You have configuration groups applied on your router.
Which command would you use to see all components of the interface hierarchy?

A. show configuration interfaces | display inheritance

B. show configuration interfaces | display changed

C. show configuration interfaces | display set

D. show configuration interfaces | display detail

Which word starts a command to display the operational status of a Junos device?

A. put

B. set

C. show

D. get

-- Exhibit --
user@router> show route
inet.0: 9 destinations, 9 routes (9 active, 0 holddown, 0 hidden)
+ = Active Route, - = Last Active, * = Both
10.10.10.91/32     *[Direct/0] 00:09:40
>via lo0.0
10.10.10.92/32     *[OSPF/10] 00:01:50, metric 1
>to 172.16.1.2 via ge-0/0/2.0
100.100.1.0/24     *[Static/5] 00:01:50
Reject -
172.16.1.0/24      *[Direct/0] 00:06:09
>via ge-0/0/2.0
172.16.1.1/32      *[Local/0] 00:06:09
Local via ge-0/0/2.0 -
192.168.0.0/16     *[Aggregate/130] 00:00:06
Reject -
192.168.0.0/17     *[Aggregate/130] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
192.168.50.0/24    *[Static/5] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
192.168.51.0/24    *[Static/5] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
user@router> show configuration policy-options
policy-statement demo {
term 1 {
from {
route-filter 192.168.0.0/16 longer accept;
}
then reject;
}
}
user@router> show configuration protocols ospf
export demo;
area 0.0.0.0 {
interface ge-0/0/2.0;
}
-- Exhibit --
Given the configuration and routing table shown in the exhibit, which routes will be advertised to OSPF neighbors because of the demo policy?

A. 192.168.0.0/16 only

B. 192.168.0.0/17 only

C. 192.168.50.0/24 and 192.168.51.0/24

D. 192.168.0.0/17, 192.168.50.0/24, and 192.168.51.0/24

-- Exhibit --
user@router> show configuration firewall
familyinet {
filter demo {
term example {
from {
source-address {
100.100.100.0/24;
}
destination-address {
200.200.200.0/24;
}
}
then {
reject;
}
}
term testing {
from {
source-address {
10.10.10.0/28;
}
destination-address {
200.200.200.0/24;
}
}
then sample;
}
term results {
from {
address {
200.200.200.0/24;
}
}
then accept;
}
term final {
thenpolicer LAPD;
}
}
}
-- Exhibit --
Given the configuration shown in the exhibit, what will happen to traffic from source 10.10.10.25 destined to 200.200.200.1?

A. The traffic will be rejected.

B. The traffic will be dropped.

C. The traffic will be forwarded.

D. The traffic will be policed.

Which two commands would you use to view OSPF routes? (Choose two.)

A. show ip route ospf

B. show ospf routes

C. show route protocol ospf

D. show route

What is the network ID address of the IPv4 subnet that includes the IP address 114.180.192.120/28?

A. 114.180.192.100/28

B. 114.180.192.118/28

C. 114.180.192.112/28

D. 114.180.192.106/28

What are two valid match criteria for a routing policy? (Choose two.)

A. OSPF area ID

B. prefix list

C. port

D. time-to-live (TTL)

Which command will display the active configuration?

A. user@router> show configuration

B. user@router# show

C. user@router> show system configuration

D. user@router> show system commit

-- Exhibit --
[edit routing-options]
user@router# show
static {
defaults {
metric 10;
preference 10;
}
route 10.10.10.0/24 {
next-hop 192.168.100.1;
qualified-next-hop 192.168.200.1;
preference 6;
}
metric 8;
}
}
-- Exhibit --
Given the configuration shown in the exhibit, which statement is correct about traffic matching the route 10.10.10.0/24?

A. It will be forwarded to 192.168.100.1 using a metric of 10.

B. It will be forwarded to 192.168.100.1 using a metric of 8.

C. It will be forwarded to 192.168.200.1 using a metric of 8.

D. It will be forwarded to 192.168.200.1 using a metric of 10.

Which interface type connects the control and forwarding planes on an MX Series device?

A. fxp1

B. fxp0

C. me0

D. ae1

Which of the following commands will configure the maximum transmission unit size of a fast Ethernet interface?

A. set interfaces fe-0/0/0 unit 0 ethernet-options mtu 1200

B. set interfaces fe-0/0/0 mtu 1200

C. set interfaces fe-0/0/0 unit 0 mtu 1200

D. set interfaces fe-0/0/0.0 mtu 1200

You are asked to configure real-time performance monitoring (RPM) between two Junos devices to track traffic in your network.
Which two application traffic types can you track? (Choose two.)

A. ICMP

B. SNMP

C. TCP

D. HTTPS

What is a route filter?

A. a list of prefixes that can be configured in a policy

B. a single prefix that is configured separately, and can be referenced in a policy

C. a list of prefixes that is configured separately and can be referenced in a policy

D. a single prefix that can be configured within a policy

What are three characteristics of UDP? (Choose three.)

A. UDP is faster than TCP.

B. UDP operates at the Transport Layer.

C. UDP is connection-oriented.

D. UDP data is sent best-effort.

E. UDP is more reliable than TCP.

Which Junos release would address only bug fixes that were not contained in the 15.1R1 version of code?

A. 15.1R2

B. 15.1X2

C. 15.1S2

D. 15.1F2

You accidentally configured interface so-0/0/0.0 with  /32 instead of  /30.
Which two solutions could you use to correct this configuration? (Choose two.)

A. [edit interfaces so-0/0/0.0] user@router# replace family inet address /32 with /30

B. [edit interfaces so-0/0/0.0] user@router# rename family inet address /32 to address /30

C. [edit] user@router# replace interface so-0/0/0.0 family inet address /32 with address /30

D. [edit interfaces so-0/0/0.0] user@router# delete family inet address

What are three acceptable modifiers to a terminating action of a firewall filter? (Choose three.)

A. Policer

B. Count

C. Syslog

D. Log

E. Discard

-- Exhibit --
user@router> show configuration
groups {
ge-int {
interfaces {
 {
unit 0 {
familyinet {
address 10.10.12.1/24;
}
}
}
}
}
}
...
interfaces {
ge-0/0/1 {
unit 0;
}
-- Exhibit --
Referring to the exhibit, which two actions would you take to only apply the 10.10.12.1/24 address to the ge-0/0/1.0 interface?

A. Apply the ge-int group to the configuration at the [edit] hierarchy.

B. Apply the ge-int group to the configuration at the [edit interfaces ge-0/0/1] hierarchy.

C. Apply the ge-int group to the configuration at the [edit interfaces ge-0/0/1 unit 0] hierarchy.

D. Apply the ge-int group to the configuration at the [edit interfaces] hierarchy.

Which process is responsible for the routing protocols on a Junos device?

A. rpd

B. mgd

C. dcd

D. chassisd

What is a valid multicast MAC address?

A. 00:90:69:9f:ea:46

B. ff:ff:ff:ff:ff:ff

C. 01:00:5e:28:12:95

D. 99:99:99:99:99:99

-- Exhibit --
[edit routing-options]
user@router# show
static {
route 0.0.0.0/0 {
next-hop 10.1.1.1;
qualified-next-hop 10.1.1.254 {
preference 4;
}
}
}
-- Exhibit --
Assuming both paths shown in the exhibit are available, which statement is correct?

A. Traffic matching the default route will use 10.1.1.1 as the next hop.

B. Traffic matching the default route will use 10.1.1.254 as the next hop.

C. Traffic matching the default route will be load-balanced per packet across both next hops.

D. Traffic matching the default route will be load-balanced per flow across both next hops.

Which command will delete the current rescue configuration?

A. user@router# system delete configuration rescue

B. user@router> request system configuration rescue delete

C. user@router# delete rescue configuration

D. user@router> file delete rescue-configuration

For the interface ge-1/2/3.4, what does "ge" represent?

A. SONET/SDH

B. Gigabit Ethernet

C. Aggregated Ethernet

D. GRE

What is the network address for the 10.13.147.100/19 host?

A. 10.13.128.0

B. 10.13.147.0

C. 10.13.0.0

D. 10.13.100.0

Which command will display the temperature of the Routing Engine's CPU?

A. show chassis environment

B. show chassis routing-engine

C. show chassis temperatures

D. show chassis status

You have configured a firewall filter with a single term matching on packets with a source address in the 10.0.0.0/24 subnet. This term only includes the count action.
Which two statements are true about traffic evaluated by this firewall filter? (Choose two.)

A. Packets outside the 10.0.0.0/24 subnet will be accepted.

B. Packets outside the 10.0.0.0/24 subnet will be rejected.

C. Packets outside the 10.0.0.0/24 subnet will be counted.

D. Packets outside the 10.0.0.0/24 subnet will not be counted.

What are two valid actions for a routing policy? (Choose two.)

A. discard

B. next policy

C. accept

D. ignore

At which command prompt would you issue the set date  command?

A. [edit chassis] user@router#

B. [edit] user@router#

C. [edit system] user@router#

D. user@router>

Which command would you use to view interface usage details in real time?

A. show interfaces terse

B. show interfaces extensive

C. monitor interface traffic

D. monitor traffic interface

At which layer of the OSI model does error checking occur with IPv6?

A. Layer 2

B. Layer 3

C. Layer 4

D. Layer 7