The output of the show frame-relay pvc command shows "PVC STATUS=INACTIVE". What does this mean?

A. The PVC is configured correctly and is operating normally, but no data packets have been detected for more than five minutes.

B. The PVC is configured correctly, is operating normally, and is no longer actively seeking the address the remote route.

C. The PVC is configured correctly, is operating normally, and is waiting for interesting to trigger a call to the remote router.

D. The PVC is configured correctly on the local switch, but there is a problem on the remote end of the PVC.

E. The PVC is not configured on the switch.

Which technology is a critical component of a cloud-based architecture?

A. DNS

B. MPLS

C. DHCP

D. IPv6

Which two components are used to identify a neighbor in a BGP configuration? (Choose two.)

A. autonomous system number

B. version number

C. router ID

D. subnet mask

E. IP address

How to configure RIPv2? (Choose two.)

A. Enable RIP

B. Connect RIP to WAN interface

C. Enable no auto-summary

D. Enable authentication

What is a valid HSRP virtual MAC address?

A. 007.4925.3020

B. 0000.0C07.AC15

C. 0007.B400.AE01

D. 0000.5E00.01A3

Which interface counter can you use to diagnose a duplex mismatch problem?

A. no carrier

B. late collisions

C. giants

D. CRC errors

E. deferred

F. runts

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)

A. Router(config)# router ospf 0

B. Router(config)# router ospf 1

C. Router(config)# router ospf area 0

D. Router(config-router)# network 192.168.16.0 0.0.0.255 0

E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0

F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0

Scenario -
 
An administrator is trying to ping and telnet from Switch to Router with the results shown below:
 
For this question we only need to use the show running-config command to answer all the questions below:
Router>enable -
Router#show running-config -
 
 
 
 
What would be the effect of issuing the command ip access-group 114 in to the fa0/0 interface?

A. Attempts to telnet to the router would fail

B. It would allow all traffic from the 10.4.4.0 network

C. IP traffic would be passed through the interface but TCP and UDP traffic would not

D. Routing protocol updates for the 10.4.4.0 network would not be accepted from the fa0/0 interface

Which statement about MPLS is true?

A. It operates in Layer 1.

B. It operates between Layer 2 and Layer 3.

C. It operates in Layer 3.

D. it operates in Layer 2.

Which command can you enter to view the ports that are assigned to VLAN 20?

A. Switch#show ip interface vlan 20

B. Switch#show vlan id 20

C. Switch#show ip interface brief

D. Switch#show interface vlan 20

For which routes does the distance bgp 10 50 70 command set the administrative distance?

A. for BGP internal routes only

B. for all BGP routes

C. between BGP routes and IGP routes

D. for BGP external routes only

A national retail chain needs to design an IP addressing scheme to support a nationwide network.
The company needs a minimum of 300 sub-networks and a maximum of 50 host addresses per subnet.
Working with only one Class B address, which of the following subnet masks will support an appropriate addressing scheme? (Choose two.)

A. 255.255.255.0

B. 255.255.255.128

C. 255.255.252.0

D. 255.255.255.224

E. 255.255.255.192

F. 255.255.248.0

When a DHCP server is configured, which two IP addresses should never be assignable to hosts? (Choose two.)

A. network or subnetwork IP address

B. broadcast address on the network

C. IP address leased to the LAN

D. IP address used by the interfaces

E. manually assigned address to the clients

F. designated IP address to the DHCP server

Which task must you perform to enable an IOS device to use DNS services?

A. Configure a relay agent information reforwarding policy.

B. Configure manual bindings.

C. Configure a name server.

D. Configure the relay agent information option.

Drag the security feature on the left to the specific security risks they help protect against on the right. (Not all options are used.)
 
Select and Place:

Refer to the exhibit.
 
You determine that Computer A cannot ping Computer B. Which reason for the problem is most likely true?

A. The subnet mask for Computer A is incorrect.

B. The default gateway address for Computer B is incorrect.

C. The subnet mask for Computer B is incorrect.

D. The default gateway address for Computer A is incorrect. A

Refer to the exhibit. If R1 sends traffic to 192.168.10.45, the traffic is sent through which interface?

A. FastEthernet0/1

B. FastEthernet0/0

C. FastEthernet1/0

D. FastEthernet1/1

Refer to the exhibit. A network associate needs to configure the switches and router in the graphic so that the hosts in VLAN3 and VLAN4 can communicate with the enterprise server in VLAN2. Which two Ethernet segments would need to be configured as trunk links? (Choose two.)
 

A. A

B. B

C. C

D. D

E. E

F. F

Refer to the exhibit.
 
What is the most efficient summarization that R1 can use to advertise its networks to R2?

A. 172.1.4.0/25 172.1.4.128/25 172.1.5.0/24 172.1.6.0/24 172.1.7.0/24

B. 172.1.0.0/22

C. 172.1.4.0/24 172.1.5.0/24 172.1.6.0/24 172.1.7.0/24

D. 172.1.0.0/21

E. 172.1.4.0/22

Which two statements about stacking Cisco switches are true? (Choose two)

A. The administrator can create only one stack of switches in a network which is under the same administrative domain.

B. Each switch manages its own MAC address table.

C. When a new master switch is elected, it queries the previous master for its running configuration.

D. The administrator can additional switches to the stack as demand increases.

E. It enables the administrator to manage multiple switches from a single management interface.

The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?

A. 8

B. 6

C. 30

D. 32

E. 14

F. 16

Refer to the exhibit.
How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?
 

A. The ports only need to be connected by a crossover cable.

B. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk

C. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-it)#switchport mode access SwitchX(config-it)#switchport access vlan 1

D. SwitchX(config)#interface fastethernet 0/1 SwitchX(config-if)#switchport mode trunk SwitchX(config-it)#switchport trunk vlan 1 SwitchX(config-if)#switchport trunk vlan 10 SwitchX(config-it)#switchport trunk vlan 20

Which command should you enter to verify the priority of a router in an HSRP group?

A. show standby

B. show interfaces

C. show sessions

D. show hsrp

What is the easiest way to verify the Layer 3 path from a router to host 192.168.2.1?

A. Execute a traceroute form the router to host 192.168.2.1

B. Add a static route for host 192.168.2.1 to the routing table of the router

C. Use Telnet to connect the router to host 192.168.2.1

D. Execute a ping form the router to host 192.168.2.1

Refer to the exhibit.
The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252.
Given the output that is shown, what three statements are true of these devices? (Choose three.)
 

A. The Manchester serial address is 10.1.1.1.

B. The Manchester serial address is 10.1.1.2.

C. The London router is a Cisco 2610.

D. The Manchester router is a Cisco 2610.

E. The CDP information was received on port Serial0/0 of the Manchester router.

F. The CDP information was sent by port Serial0/0 of the London router.

Frame flooding can occur in which circumstances?

A. The destination IP address is missing from the route table.

B. The destination MAC address is missing from the CAM table.

C. The source IP address is missing from the route table.

D. The source MAC address is missing from the CAM table.

Which statement describes the process of dynamically assigning IP addresses by the DHCP server?

A. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.

B. Addresses are permanently assigned so that the hosts uses the same address at all times.

C. Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.

D. Addresses are leased to hosts, which periodically contact the DHCP server to renew the lease.

Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network address?

A. 172.16.16.0

B. 172.16.0.0

C. 172.16.24.0

D. 172.16.28.0

In order to comply with new auditing standards, a security administrator must be able to correlate system security alert logs directly with the employee who triggers the alert. Which of the following should the security administrator implement in order to meet this requirement?

A. Access control lists on file servers

B. Elimination of shared accounts

C. Group-based privileges for accounts

D. Periodic user account access reviews

Which address class includes network 191.168.0.1/27?

A. Class C

B. Class B

C. Class D

D. Class A

Refer to the exhibit.
 
A network administrator cannot establish a Telnet session with the indicated router. What is the cause of this failure?

A. A Level 5 password is not set.

B. An ACL is blocking Telnet access.

C. The vty password is missing.

D. The console password is missing.

After you apply the given configuration to R1, you notice that it failed to enable OSPF.
Which action can you take to correct the problem?
 

A. Configure a loopback interface on R1

B. Enable IPv6 unicast routing on R1.

C. Configure an IPv4 address on interface F0/0.

D. Configure an autonomous system number on OSPF.

Which two statistics appear in show frame-relay map output? (Choose two.)

A. the number of BECN packets that are received by the router

B. the value of the local DLCI

C. the number of FECN packets that are received by the router

D. the status of the PVC that is configured on the router

E. the IP address of the local router

A router receives information about network 192.168.10.0/24 from multiple sources.
What will the router consider the most reliable information about the path to that network?

A. an OSPF update for network 192.168.0.0/16.

B. a static router to network 192.168.10.0/24.

C. a static router to network 192.168.10.0/24 with a local serial interface configured as the next hop.

D. a RIP update for network 192.168.10.0/24.

E. a directly connected interface with an address of 192.168.10.254/24.

F. a default route with a next hop address of 192.168.10.1 416.

Refer to the exhibit. According to the routing table, where will the router send a packet destined for 10.1.5.65?
 

A. 10.1.1.2

B. 10.1.2.2

C. 10.1.3.3

D. 10.1.4.4

Refer to the exhibit.
 
A new subnet with 60 hosts has been added to the network. Which subnet address should this network use to provide enough usable addresses while wasting the fewest addresses?

A. 192.168.1.56/26

B. 192.168.1.56/27

C. 192.168.1.64/26

D. 192.168.1.64/27

Refer to the exhibit.
 
Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure?
(Choose two.)

A. The cable that is connected to S0/0 on RouterA is faulty.

B. Interface S0/0 on RouterB is administratively down.

C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.

D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.

E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.

F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.

Which statement describes the process of dynamically assigning IP addresses by the DHCP server?

A. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.

B. Addresses are permanently assigned so that the hosts uses the same address at all times.

C. Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.

D. Addresses are leased to hosts, which periodically contact the DHCP server to renew the lease.

What are the popular destinations for Syslog messages to be saved?

A. Flash

B. Syslog server

C. The logging buffer .RAM

D. The console terminal

E. Other terminals

Refer to the exhibit.
 
The two exhibited devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? (Choose three.)

A. The Manchester serial address is 10.1.1.1.

B. The Manchester serial address is 10.1.1.2.

C. The London router is a Cisco 2610.

D. The Manchester router is a Cisco 2610.

E. The CDP information was received on port Serial0/0 of the Manchester router.

F. The CDP information was sent by port Serial0/0 of the London router.

You apply a new inbound access list to routers, blocking UDP packets to the HSRP group. Which two effects does this action have on the HSRP group process?
(Choose two.)

A. HSRP redundancy works as expected

B. Both the active and standby routers become active

C. The active router immediately becomes the standby router.

D. HSRP redundancy fails.

E. The routers in the group generate duplicate IP address warnings

Which two tasks can help you gather relevant facts when you troubleshoot a network problem?
(Choose two.)

A. Change one setting or component and then analyze the result.

B. Eliminate known issues first.

C. Collect technical data from network management systems and logging servers.

D. Define the problem in terms of symptoms and causes.

E. Ask questions of the users who are affected by the problem.

A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?

A. session

B. transport

C. network

D. data link

E. physical

What is the danger of the permit any entry in a NAT access list?

A. It can lead to overloaded resources on the router

B. It can cause too many addresses to be assigned to the same interface.

C. It can disable the overload command.

D. It prevents the correct translation of IP addresses on the inside network.

Which value must the device send as its username when using CHAP to authenticate with the remote peer site id: XXXXXXXX over a PPP link?

A. The automatically generated user name

B. The local host name

C. The user name defined by the administrator

D. The host name of the remote device.

Which two benefits can you get by stacking Cisco switches? (Choose two.)

A. Each switch in the stack handles the MAC table independently from the others

B. You can add or remove switches without taking the stack down.

C. Each switch in the stack can use a different IOS image

D. The stack enables any active member to take over as the master switch if the existing master fails.

E. You can license the entire stack with a single master license

Refer to the exhibit. A new subnet with 60 hosts has been added to the network.
Which subnet address should this network use to provide enough usable addresses while wasting the fewest addresses?
 

A. 192.168.1.56/27

B. 192.168.1.64/26

C. 192.168.1.64/27

D. 192.168.1.56/26

In a GLBP network, who is responsible for the arp request?

A. AVF

B. AVG

C. Active router

D. Standby Router

Refer to the exhibit.
 
Which address range efficiently summarizes the routing table of the addresses for router Main?

A. 172.16.0.0./21

B. 172.16.0.0./20

C. 172.16.0.0./16

D. 172.16.0.0/18

Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency? (Choose two.)

A. mismatched process IDs

B. mismatched autonomous system numbers

C. an ACL blocking traffic from multicast address 224.0.0.10

D. use of the same router ID on both devices

E. mismatched hello timers and dead timers