Click the Exhibit button.
Referring to the outputs shown in the exhibit, which two statements are correct about the IS-IS adjacency? (Choose two.)
 

A. R1 is configured to participate in both Level 1 and Level 2.

B. R2 is configured to participate in both Level 1 and Level 2.

C. R1 is configured to participate in Level 2 only.

D. R2 is configured to participate in Level 2 only.

Which three statements are correct about EVPN route types? (Choose three.)

A. Type 3 routes carry replication information.

B. Type 2 routes carry endpoint MAC address information.

C. Type 2 routes carry endpoint IP address information.

D. Type 5 routes carry replication information.

E. Type 1 routes carry endpoint MAC address information.

You are asked to configure 802.1X on your access ports to allow only a single device to authenticate.
In this scenario, which configuration would you use?

A. single supplicant mode

B. multiple supplicant mode

C. single-secure supplicant mode

D. MAC authentication mode

Click the Exhibition button.
Referring to the exhibit, ServerA sends a single IP packet destined to 10.0.0.127.
Which two statements correctly describe the behavior of the resulting outbound VXLAN packets that contain the original packet destined to 10.0.0.127? (Choose two.)
 

A. Router E will replicate and send a copy of the received VXLAN packet to router D.

B. Router C will send a VXLAN packet destined only to router D and router E.

C. Router D will not replicate and send a copy of the received VXLAN packet to router E.

D. Router C will send a single VXLAN packet to one remote VTEP.

You enable the Multiple VLAN Registration Protocol (MVRP) to automate the creation and management of virtual LANs.
Which statement is correct in this scenario?

A. The forbidden mode does not register or declare VLANs.

B. When enabled, MVRP affects all interfaces.

C. Timers dictate when link state changes are propagated.

D. MVRP works with RSTP and VSTP.

Click the Exhibit button.
Referring to the exhibit, which LSA type is used to advertise 192.168.1.0/24 to R5?
 

A. Type 5

B. Type 4

C. Type 3

D. Type 7

You are deploying IP phones in your enterprise network that must receive their power through their Ethernet connection. You are using your EX Series switch's PoE ports that support IEEE 802.3af.
In this scenario, what is the maximum amount of power allocated to each interface?

A. 10.2 W

B. 15.4 W

C. 30 W

D. 50 W

Click the Exhibit button.
You recently committed a change to a router to reject OSPF routes sourced from area 10. However, you are still seeing area 10 routes in the routing table.
Referring to the exhibit, which statement is correct?
 

A. The OSPF protocol is first matched by find-ospf and accepted.

B. The routes only timeout after 24 hours.

C. The routes remain in the table until the device is rebooted.

D. The routes remain in the table until the routing daemon is restarted.

Click the Exhibit button.
Referring to the exhibit, which statement is correct when a failure exists on the link between host2 and switch5 on this EVPN-VXLAN fabric?
 

A. The switch5 device will send a Type 2 route to all peers.

B. The switch5 device will send a Type 4 route to all peers.

C. The switch5 device will send a Type 1 route to all peers.

D. The switch5 device will send a Type 3 route to all peers.

You are asked to establish interface level authentication for users connecting to your network. You must ensure that only corporate devices, identified by MAC addresses, are allowed to connect and authenticate. Authentication must be handled by a centralized server to increase scalability.
Which authentication method would satisfy this requirement?

A. MAC RADIUS

B. captive portal

C. 802.1X with single-secure supplicant mode

D. 802.1X with multiple supplicant mode

BGP multipath or multihop are not configured in your network.
In this scenario, what is the correct sequence for BGP active route selection?

A. higher local preferenceshortest AS pathlowest peer addresslowest router IDlower origin code

B. higher local preferenceshortest AS pathlower origin codelowest router IDlowest peer address

C. higher local preferencelowest router IDlowest peer addresslower origin codeshortest AS path

D. higher local preferenceshortest AS pathlowest router IDlowest peer addresslower origin code

Click the Exhibit button.
Referring to the exhibit, which two statements are correct? (Choose two.)
 

A. The host that the route is associated with is multihomed to two leaf nodes.

B. The route is a Type 1 EVPN route.

C. The route is a Type 2 EVPN route.

D. The host that the route is associated with is single-homed to one leaf node.

Click the Exhibit button.
You are asked to establish full connectivity between all devices in the BGP network.
Referring to the exhibit, which two configuration changes will allow BGP route advertisements? (Choose two.)
 

A. On R2, include the loops 2 statement at the [edit protocols bgp family inet unicast] hierarchy.

B. On R1 and R3, include the loops 2 statement at the [edit protocols bgp family inet unicast] hierarchy.

C. On R1 and R3, include the advertise-peer-as statement at the [edit protocols bgp group external] hierarchy.

D. On R2, include the advertise-peer-as statement at the [edit protocols bgp group external] hierarchy.

You must ensure that all routes in the 10.0.0/8 address range are not advertised outside of your AS.
Which well-known BGP community should be assigned to these addresses to accomplish this task?

A. no-export

B. no-peer

C. internet

D. no-advertise

When using wide metrics, which two statements about route advertisement between IS-IS levels are correct? (Choose two.)

A. Level 1 and Level 2 routers do not advertise Level 2 routes into the Level 1 area by default.

B. Level 1 routes are advertised to Level 2 routers by default.

C. If wide-metrics-only is configured, Level 1 routes are not advertised to Level 2 routers by default.

D. Level 1 routes advertised as external routes into Level 1 are not advertised to any Level 2 routers by default.

Click the Exhibit button.
Referring to the exhibit, how will router E quickly learn that the remote MAC addresses are no longer reachable through the router attached to the failed link?
 

A. Router E receives Type 2 withdrawal messages from router D.

B. Router E receives Type 1 withdrawal messages from router D.

C. Router E receives Type 1 withdrawal messages from router C.

D. Router E receives Type 2 withdrawal messages from router C.

You are asked to enforce user authentication using a captive portal before users access the corporate network.
Which statement is correct in this scenario?

A. HTTPS is the default protocol for a captive portal.

B. A captive portal can be bypassed using an allowlist command containing a device’s IP address.

C. When enabled, a captive portal must be applied to each individual interface.

D. All Web browser requests are redirected to the captive portal until authentication is successful.

Click the Exhibit button.
You have scheduled maintenance operations for one of the devices in your OSPF network.
Referring to the exhibit, which three statements are correct? (Choose three.)
 

A. R1 does not participate in OSPF routing.

B. Any traffic destined for networks that terminate on R1 will still be forwarded to R1.

C. The metrics for all transit interfaces on R1 is set to the maximum value of 65,535.

D. R1 participates in OSPF routing but does not send or receive transit traffic.

E. R1 does not send or receive transit traffic during the maintenance window even if no alternative paths exist to the given destination.

Click the Exhibit button.
Remote branches connect to the corporate WAN through access switches. The access switches connect to access ports on the WAN distribution switch, as shown in the exhibit. L2PT has previously been configured on the tunnel Layer 2 traffic across the WAN. You decide to move the L2PT tunnel endpoints to the access switches. When you apply the L2PT configuration to the access switches, the ports that connect the access switches to the distribution switch shut down.
Which action would solve this problem?
 

A. Configure the links between the access switches and the distribution switch as a trunk port.

B. Disable the BPDU block function on the access switches.

C. Disable the BPDU block function on the distribution switch.

D. Configure a GRE tunnel to encapsulate the L2PT traffic across the WAN.

You are asked to implement fault tolerant RPs in your multicast network.
Which two solutions would accomplish this behavior? (Choose two.)

A. Use BFD with statically defined RPs.

B. Use MSDP with statically defined RPs.

C. Use anycast PIM with statically defined RPs.

D. Use IGMPv3 with statically defined RPs.

Click the Exhibit button.
You are running OSPF as your IGP. The interfaces connecting two routers are in the ExStart state. You notice that something is incorrect with the configuration.
Referring to the exhibit, which statement is correct?
 

A. The subnet mask is incorrect.

B. The MTU setting are incorrect.

C. The interface type is incorrect.

D. The IP addresses are incorrect.

Click the Exhibition button.
A BGP network has been designed to provide resiliency and redundancy to a multihomed customer network.
Which two statements are correct in this scenario? (Choose two.)
 

A. Both the next hops will be used to forward traffic to R2.

B. A routing policy will be required to forward traffic to both next hops.

C. The TTL value of 1 is set to limit the scope of the EBGP session.

D. The ttl statement must be configured to accommodate peering to a loopback address of a directly connected peer.

Your network is multihomed to two ISPs. The BGP sessions are established; however, the ISP peers are not receiving any routes.
Which two statements are correct about troubleshooting your configuration? (Choose two.)

A. Verify the import policies on your router.

B. Verify that the BGP routes are active in your routing table.

C. Verify the export policies on your router.

D. Verity that the multihop settings are configured on your router.

Click the Exhibit button.
You want to provide Layer 2 connectivity between campus sites using Ethernet switches through a metro Ethernet service provider who is using Q-in-Q tagging on their network.
Referring to the exhibit, what are two design considerations in this environment? (Choose two.)
 

A. VXLAN could be implemented on your network across this service provider network.

B. Each campus switch shown must have a C-Tag 300 configured.

C. L2PT is required on the SP network to support the spanning tree protocol.

D. Each campus switch shown must have S-Tag 300 configured.

You are deploying an 802.1X solution and must determine what would happen if clients are unable to re-authenticate to the RADIUS server.
In this scenario, which configuration would provide access to the network if the supplicant is already authenticated?

A. move

B. permit

C. deny

D. sustain

Which address range is used for source-specific multicast?

A. 239.0.0.0/8

B. 233.0.0.0/8

C. 232.0.0.0/8

D. 224.2.0.0/16

Click the Exhibit button.
Which two statements are correct regarding the behavior shown in the exhibit? (Choose two.)
 

A. The ge-1/1/0 interface is configured as secondary for Area 0.

B. The router is an ABR.

C. The router is not an ABR.

D. The ge-1/1/0 interface is configured as secondary for Area 100.

Click the Exhibit button.
Referring to the exhibit, which two statements are correct? (Choose two.)
 

A. The maximum wattage that this switch can allocate to attached Ethernet devices is 100 watts.

B. If the total power consumption exceeds 90 watts, the ge-0/0/11 interface will continue to receive power.

C. PoE is not enabled on the ge-0/0/0 interface.

D. The ge-0/0/10 interface supports PoE+.

You want to create an OSPF area that only contains intra-area route information in the form of Type 1 and Type 2 LSAs.
In this scenario, which area is needed to accomplish this task?

A. totally non-to-stubby area

B. totally stubby area

C. stub area

D. non-to-stubby area

Click the Exhibit button.
Referring to the exhibit, anycast RP is implemented to ensure multicast service availability. The source is currently sending multicast traffic using group 239.1.1.1 and R3 is receiving PIM register messages, but R2 does not have active source information.
In this scenario, what are two methods to receive the active source information on R2? (Choose two.)
 

A. Configure an RP set in PIM on R1, allowing R1 to forward PIM register messages to R2 and R3 in the set.

B. Configure an MSDP protocol between R2 and R3.

C. Configure an RP set in PIM on R2 and R3, allowing the RPs to forward PIM register messages to the other RPs in the set.

D. Configure an MSDP protocol between R1 and R2.

You are deploying new Juniper EX Series switches in a network that currently is using Cisco’s Per-VLAN spanning tree plus (PVST+) and you must provide compatibility with this environment.
Which spanning tree protocol do you deploy in this scenario?

A. STP

B. MSTP

C. VSTP

D. RSTP

You are implementing the route summarization feature of OSPF.
Which two results do you achieve in this scenario? (Choose two.)

A. It helps in migrating to future multi-area OSPF network designs.

B. It reduced the routing table size, enabling devices to store and process less information.

C. It reduces the impact of topology changes on a device.

D. It provides optimal routing in the network.

Click the Exhibit button.
Referring to the exhibit, which statement is correct?
 

A. The route is learned from a multihop BGP session.

B. The route is learned from only one neighbor.

C. The route is learned from a multipath BGP session.

D. The route is learned from three different neighbors.

A modified deficit round-robin scheduler is defined by which three variables? (Choose three.)

A. priority

B. WRED

C. transmit rate

D. Layer 3 fields

E. buffer size

You must provide network connectivity to hosts that fail authentication.
In this scenario, what would be used in a network secured with 802.1X to satisfy this requirement?

A. Configure the native-vlan-id parameter on the port.

B. Use the server-reject-vlan command to specify a guest VLAN.

C. Configure a secondary IP address on the port for unauthenticated hosts.

D. Configure the port as a spanning tree edge port.

Which two statements are correct about the deployment of EVPN-VXLAN on QFX Series devices? (Choose two.)

A. Type 1 route advertisements always have the single-active flag set to 1.

B. Junos OS supports underlay replication for BUM traffic forwarding.

C. Junos OS supports ingress replication for BUM traffic forwarding.

D. Type 1 route advertisements always have the single-active flag set to 0.

Click the Exhibit button.
You are troubleshooting an EVPN-VXLAN IP fabric and observe the loop shown in the exhibit.
Which two steps would you take to further troubleshoot this problem? (Choose two.)
 

A. Verify that the same ESI is configured on the link from the host and that it matches the source.

B. Issue the show route table bgp.evpn.0 command on Leaf2 and verify that Type 4 routes are present.

C. Issue the show route table bgp.evpn.0 command on Leaf2 and verify that Type 3 routes are present.

D. Verify that the same ESI is configured on the two links from the source.

Click the Exhibit button.
Referring to the exhibit, which two statements are correct? (Choose two.)
 

A. The DS-2 switch will be root bridge for MSTI 2.

B. The DS-1 switch will be root bridge for MSTI 1.

C. The DS-1 switch will be root bridge for MSTI 2.

D. The DS-2 switch will be root bridge for MSTI 1.

Click the Exhibition button.
You are asked to troubleshoot voice quality issues on your newly implement VoIP network. You notice that the voice packets are being dropped. You have verified that the packets are correctly marked for expedited forwarding queue.
Referring to the exhibit, what must you configure to solve the problem?
 
 
 

A. You must configure a multifield classifier to put the VoIP traffic in the correct queue.

B. You must configure a rewrite rule to ensure that the traffic is scheduled properly in the device.

C. You must configure a scheduler to allocate bandwidth to the expedited forwarding queue.

D. You must configure a policer to ensure that the queue is not being starved.

Which three configuration parameters must match on all switches within the same MSTP region? (Choose three.)

A. VLAN to instance mapping

B. revision level

C. configuration name

D. bridge priority

E. region name

Which statement is correct about IS-IS?

A. IS-IS uses areas and an autonomous system.

B. Level 1/2 routers automatically inject a default route to the nearest Level 1 router.

C. Level 2 routers must share the same area address.

D. Level 1 routers route traffic between autonomous systems.

You are deploying IP phones in your enterprise networks. When plugged in, the IP phones must automatically negotiate the power requirements for the new connection with the EX Series switches.
In this scenario, which protocol should be used to enable this behavior?

A. CDP

B. MP-BGP

C. LLDP-MED

D. LLDP

Click the Exhibit button.
Referring to the exhibit, a PIM-SM network is set up to enable communication between multicast devices.
Which two statements are true? (Choose two.)
 

A. Before the formation of the rendezvous-point tree, a join message is sent from R1 to R3.

B. Before the formation of the rendezvous-point tree, an IGMP is sent from the Receiver to R1.

C. Before the formation of the rendezvous-point tree, an IGMP is sent from the Source to R5.

D. Before the formation of the rendezvous-point tree, a join message is sent from R1 to R5.

You are using 802.1X authentication in your network to secure all ports. You have a printer that does not support 802.1X and you must ensure that traffic is allowed to and from this printer without authentication.
In this scenario, what will satisfy the requirement?

A. MAC filtering

B. MACsec

C. static MAC bypass

D. MAC RADIUS

Your enterprise network is running BGP VPNs to support multitenancy. Some of the devices with which you peer BGP do not support the VPN NLRI. You must ensure that you do not send BGP VPN routes to the remote peer.
Which two configuration steps will satisfy this requirement? (Choose two.)

A. Configure an import policy on the remote peer to reject the routes when they are received.

B. Configure an export policy on the local BGP peer to reject the VPN routes being sent to the remote peer.

C. Configure a route reflector for the VPN NLRI.

D. Configure the apply-vpn-export feature on the local BGP peer.

Which three MSTP parameters must match on all switches in the same MST region? (Choose three.)

A. forwarding delay

B. bridge priority

C. revision number

D. MSTI-to-VLAN mapping

E. configuration name

Click the Exhibit button.
A user is attempting to watch a high-definition video being streamed from the media server over the network. However, the user complains that the experienced video quality is poor. While logged on to router B, a Juniper Networks device, you notice that video packets are being dropped.
In this scenario, what would solve this problem?
 

A. Adjust the scheduler for the expedited-forwarding forwarding class to support a higher transmit rate.

B. Adjust the expedited-forwarding BA classifier to router B’s ge-0/0/0 interface to support a higher transmit rate.

C. Adjust the scheduler-map to support a higher transmit rate.

D. Adjust the expedited-forwarding BA classifier on router B’s ge-0/0/1 interface to support a higher transmit rate.

Your organization has recently acquired another company. You must carry all of the company’s existing VLANs across the corporate backbone to the existing branch locations without changing addressing and with minimal configuration.
Which technology will accomplish this task?

A. Q-in-Q all-in-one bundling

B. PVLAN isolated VLAN

C. MVRP registration normal

D. EVPN-VXLAN anycast gateway

Click the Exhibit button.
Referring to the exhibit, which two statements are correct? (Choose two.)
 
 

A. The BGP neighbor can advertise L3 VPN related routes.

B. The BGP neighbor cannot advertise EVPN related routes.

C. The BGP neighbor can advertise EVPN related routes.

D. The BGP neighbor cannot advertise L3 VPN related routes.

You are asked to configure an 802.1X solution that supports dynamic VLAN assignment.
In this scenario, which two modes support using vendor-specific attributes (VSAs)? (Choose two.)

A. static MAC bypass mode

B. single-secure supplicant mode

C. multiple supplicant mode

D. single supplicant mode