What is a characteristic of IPv6 RA Guard?

A. It lters rogue RA broadcasts from connected hosts.

B. It is supported on the egress direction of the switch.

C. RA messages are allowed from the host port to the switch.

D. It is unable to protect tunneled traffic.

Refer to the exhibit. An engineer configures the router 10.1.100.10 for EIGRP autosummarization so that R1 should receive the summary route of 10.0.0.0/8.
However, R1 receives more specific /24 routes.
Which action resolves this issue?

A. Router R1 should configure ip summary address eigrp (AS number) 10.0.0.0 255.0.0.0 for the R1 Fast Ethernet 0/0 connected interface.

B. Router R1 should configure ip route 10.0.0.0 255.0.0.0 null 0 for the routes that are received on R1.

C. Router 10.1.100.10 should configure ip route 10.0.0.0 255.0.0.0 null 0 for the routes that are summarized toward R1.

D. Router 10.1.100.10 should configure ip summary address eigrp (AS number) 10.0.0.0 255.0.0.0 for the R1 Fast Ethernet 0/0 connected interface.

The network administrator configured R1 for Control Plane Policing so that the inbound Telnet traffic is policed to 100 kbps. This policy must not apply to traffic coming in from 10.1.1.1/32 and 172.16.1.1/32. The administrator has configured this: access-list 101 permit tcp host 10.1.1.1 any eq 23 access-list 101 permit tcp host 172.16.1.1 any eq 23
class-map CoPP-TELNET
match access-group 101
policy-map PM-CoPP
class CoPP-TELNET
police 100000 conform transmit exceed drop
control-plane
service-policy input PM-CoPP
The network administrator is not getting the desired results.
Which set of configurations resolves this issue?

A. no access-list 101 access-list 101 deny tcp host 10.1.1.1 any eq 23 access-list 101 deny tcp host 172.16.1.1 any eq 23 access-list 101 permit ip any any

B. control-plane no service-policy input PM-CoPP ! interface Ethernet 0/0 service-policy input PM-CoPP

C. no access-list 101 access-list 101 deny tcp host 10.1.1.1 any eq 23 access-list 101 deny tcp host 172.16.1.1 any eq 23 access-list 101 permit ip any any ! Interface E 0/0 service-policy input PM-CoPP

D. control-plane no service-policy input PM-CoPP service-policy input PM-CoPP

A customer reports to the support desk that they cannot print from their PC to the local printer id:123456789. Which tool must be used to diagnose the issue using Cisco DNA Center Assurance?

A. device trace

B. ACL trace

C. path trace

D. application trace

Refer to the exhibit. Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day.
Which action xes the issue within the current resources?

A. Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool

B. configure the DHCP lease time to a smaller value

C. configure the DHCP lease time to a bigger value

D. Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool

What is a characteristic of an MPLS LSP tunnel?

A. bidirectional tunnel

B. secured bidirectional tunnel

C. hop-by-hop tunnel

D. unidirectional tunnel

Refer to the exhibit. A network administrator is discovering a Cisco Catalyst 9300 and a Cisco WLC 3504 in Cisco DNA Center. The Catalyst 9300 is added successfully. However, the WLC is showing the error "uncontactable" when the administrator tries to add it in Cisco DNA Center.
Which action discovers WLC in Cisco DNA Center successfully?

A. Delete the WLC 3504 from Cisco DNA Center and add it to Cisco DNA Center again.

B. Add the WLC 3504 under the hierarchy of the Catalyst 9300 connected devices.

C. Copy the .cert file from the Cisco DNA Center on the USB and upload it to the WLC 3504.

D. Copy the .pem file from the Cisco DNA Center on the USB and upload it to the WLC 3504.

Refer to the exhibit. Routing protocols are mutually redistributed on R3 and R1. Users report intermittent connectivity to services hosted on the 10.1.1.0/24 prefix.
significant routing update changes are noticed on R3 when the show ip route profile command is run.
How must the services be stabilized?

A. The routing loop must be fixed by reducing the admin distance of OSPF from 110 to 80 on R3

B. The routing loop must be fixed by reducing the admin distance of iBGP from 200 to 100 on R3

C. The issue with using BGP must be resolved by using another protocol and redistributing it into EIGRP on R3

D. The issue with using iBGP must be fixed by running eBGP between R3 and R4

Refer to the exhibit. An engineer is investigating an OSPF issue reported by the Cisco DNA Assurance Center. Which action resolves the issue?

A. One of the interfaces is using the wrong MTU. Match interface MTU on both links.

B. One of the interfaces is using the wrong authentication. Match interface authentication on both links.

C. One of the neighbor links is down. Bring the interface up by running shut and no shut.

D. An ACL entry blocking multicast on the interfaces. Allow multicast through the interface ACL.

Refer to the exhibit. The Customer Edge router wants to use AS 100 as the preferred ISP for all external routes and SP2 as a backup.
Customer-Edge -
route-map SETAS
set as-path prepend 111
router bgp 64555
neighbor 192.168.1.1 remote-as 100
neighbor 192.168.2.2 remote-as 200
neighbor 192.168.2.2 route-map SETAS in
After this configuration, all the backup routes have disappeared from the BGP table on the Customer Edge router. Which set of configurations resolves the issue on the Customer Edge router?

A. route-map SETAS
set as-path prepend 200
router bgp 64555
neighbor 192.168.1.1 remote-as 100
neighbor 192.168.2.2 remote-as 200
neighbor 192.168.2.2 route-map SETAS in

B. route-map SETAS
set as-path prepend 111
router bgp 64555
neighbor 192.168.1.1 remote-as 100
neighbor 192.168.2.2 remote-as 200
neighbor 192.168.2.2 route-map SETAS out

C. route-map SETAS
set as-path prepend 200
router bgp 64555
neighbor 192.168.1.1 remote-as 100
neighbor 192.168.2.2 remote-as 200
neighbor 192.168.2.2 route-map SETAS out

D. route-map SETAS
set as-path prepend 111
router bgp 64555
neighbor 192.168.2.2 remote-as 100
neighbor 192.168.1.1 remote-as 200
neighbor 192.168.1.1 route-map SETAS in

Refer to the exhibit. An engineer recently implemented uRPF by configuring the ip verify unicast source reachable-via rx command on interface gi0/3. The engineer noticed right after implementing uRPF that an inbound packet on the gi0/3 interface with a source address of 172.16.3.251 was dropped. Which action resolves the issue?

A. configure uRPF loose mode to forward the packet.

B. Permit the 172.16.3.251 in the inbound ACL on interface gi0/3.

C. Remove inbound ACL from the interface gi0/3 to allow 172.16.3.251.

D. configure uRPF strict mode to forward the packet.

A network engineer is investigating a apping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the ap.
Which command allows the logging on the switch to show the time of the ap according to the clock on the device?

A. service timestamps log uptime

B. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00

C. service timestamps log datetime localtime show-timezone

D. clock calendar-valid

Refer to the exhibit. The network administrator configured VRF lite for customer

A. The technician at the remote site misconfigured VRF on the router.
Which configuration will resolve connectivity for both sites of customer_a?

B.

C.

D.

E.

Refer to the exhibit. Which configuration resolves the IP SLA issue from R1 to the server?

A. R6(config)#ip sla responder

B. R6(config)#ip sla 650 R6(config-ip-sla)#udp-jitter 10.60.60.6

C. R6(config)#ip sla responder udp-echo ipaddress 10.60.60.6 po 5000

D. R6(config)#ip sla schedule 10 life forever start-time now

Refer to the exhibit. A network is configured for EIGRP equal-cost load balancing, but the traffic destined to the servers is not load balanced. Link metrics from router R2 to R3 and R4 are the same. Which delay value must be configured to resolve the issue?

A. 2200 on R4 E0/1

B. 200 on R3 E0/1

C. 120 on R3 E0/1

D. 120 on R4 E0/1

Refer to the exhibit. Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?

A.

B.

C.

D.

An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VR

A. Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red?

B. router ospf 1 vrf blue
network 10.10.10.0 0.0.0.252 area 0
router ospf 2 vrf red
network 192.168.0.0 0.0.0.240 area 0

C. router ospf 1 vrf blue
network 10.10.10.0 0.0.0.15 area 0
router ospf 2 vrf red
network 192.168.0.0 0.0.0.3 area 0

D. router ospf 1 vrf blue
network 10.10.10.0 0.0.0.240 area 0
router ospf 2 vrf red
network 192.168.0.0 0.0.0.252 area 0

E. router ospf 1 vrf blue
network 10.10.10.0 0.0.0.3 area 0
router ospf 2 vrf red
network 192 168.0.0 0.0.0.15 are 0

When determining if a system is capable of support, what is the minimum time spacing required for a BFD control packet to receive once a control packet is arrived?

A. Desired Min TX Interval

B. Detect Mult

C. Required Min RX Interval

D. Required Min Echo RX Interval

Refer to the exhibit. An engineer is trying to get 192.168.32.100 forwarded through 10.1.1.1, but it was forwarded through 10.1.1.2. What action forwards the packets through 10.1.1.1?

A. configure EIGRP to receive 192.168.32.0 route with lower metric.

B. configure EIGRP to receive 192.168.32.0 route with lower admin distance.

C. configure EIGRP to receive 192.168.32.0 route with longer prefix than /19.

D. configure EIGRP to receive 192.168.32.0 route with equal or longer prefix than /24.

Refer to the exhibit. After reloading the router, an administrator discovered that the interface utilization graphs displayed inconsistencies with their previous history in the NMS.
Which action prevents this issue from occurring after another router reload in the future?

A. configure SNMP interface index persistence on the router.

B. Save the router configuration to startup-config before reloading the router.

C. Rediscover all the router interfaces through SNMP after the router is reloaded.

D. configure SNMP to use static OIDs referring to individual router interfaces.

SIMULATION
-
 
Guidelines
-
This is a lab item in which tasks will be performed on virtual devices.
•	Refer to the Tasks tab to view the tasks for this lab item.
•	Refer to the Topology tab to access the device console(s) and perform the tasks.
•	Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
•	All necessary preconfigurations have been applied.
•	Do not change the enable password or hostname for any device.
•	Save your configurations to NVRAM before moving to the next item.
•	Click Next at the bottom of the screen to submit this lab and move to the next question.
•	When Next is clicked, the lab closes and cannot be reopened.
Topology
-
 
Tasks
-
Troubleshoot R-WEST to achieve the desired results:
1. All the commands should be locally saved to the router as well as sent to the Syslog server except passwords.
2. All the Cisco OSPF LSA traps should be sent to the SNMP server.

Refer to the exhibit. An administrator must configure the router with OSPF for IPv4 and IPv6 networks under a single process. The OSPF adjacencies are not established and did not meet the requirement. Which action resolves the issue?

A. Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv4 address, and remove process 10 from the global configuration.

B. Replace OSPF process 10 on the interfaces with OSPF process 1, and configure an additional router ID with IPv6 address.

C. Replace OSPF process 10 on the interfaces with OSPF process 1, and remove process 10 from the global configuration.

D. Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv6 address, and remove process 10 from the global configuration.

Refer to the exhibit. Clients on ALS2 receive IPv4 and IPv6 addresses, but clients on ALS1 receive only IPv4 addresses and not IPv6 addresses.
Which action on
DSW1 allows clients on ALS1 to receive IPv6 addresses?

A. configure DSW1(dhcp-config)#default-router 2002:A04:A01::A04:A01

B. configure DSW1(config-if)#ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet1/2

C. configure DSW1(config)#ipv6 route 2002:404:404::404:404/128 FastEthernet1/0

D. configure DSW1(config-if)#ipv6 helper address 2002:404:404::404:404

Refer to the exhibit. An engineer configured NetFlow on R1, but the ows do not reach the NMS server from R1. Which configuration resolves this issue?

A. R1(config)# flow monitor FlowMonitort1
R1(config- flow-monitor)#destination 10.66.66.66

B. R1(config)#interface Ethernet0/0
R1(config-if)#ip flow monitor Flowmonitor1 input
R1(config-if)#ip flow monitor Flowmonitor1 output

C. R1(config)#interface Ethernet0/1
R1(config-if)#ip flow monitor Flowmonitor1 input
R1(config-if)#ip flow monitor Flowmonitor1 output

D. R1(config)# flow exporter FlowExporter1
R1(config- flow-exporter)#destination 10.66.66.66

Refer to the exhibit. EIGRP adjacency between router A and router C is not working as expected. Which two configurations resolve the issue? (Choose two.)

A.

B.

C.

D.

E.

Refer to the exhibit. R1 cannot authenticate via TACACS. Which configuration resolves the issue?

A. aaa group server tacacs+ DC1_TACACS
server name DC_TACACS

B. tacacs server DC1_TACACS
address ipv4 10.66.66.66
key D@t@c3nter1TACACS

C. tacacs server DC1_TACACS
address ipv4 10.60.66.66
key D@t@c3nter1TACACS

D. aaa group server tacacs+ DC_TACACS
server name DC_TACACS

Refer to the exhibit. The IT router has been configured with the Science VRF and the interfaces have been assigned to the VR

A. Which set of configurations advertises Science-1 and Science-2 routes using EIGRP AS 111?

B. router eigrp 111 address-family ipv4 vrf Science autonomous-system 1 network 192.168.1.0 network 192.168.2.0

C. router eigrp 111 address-family ipv4 vrf Science network 192.168.1.0 network 192.168.2.0

D. router eigrp 111 network 192.168.1.0 network 192.168.2.0

E. router eigrp 1 address-family ipv4 vrf Science autonomous-system 111 network 192.168.1.0 network 192.168.2.0

Refer to the exhibits. A user on the 192.168.1.0/24 network can successfully ping 192.168.3.1, but the administrator cannot ping 192.168.3.1 from the LA router.
Which set of configurations xes the issue?

A.

B.

C.

D.

Refer to the exhibit. Which configuration enables OSPF for area 0 interfaces to establish adjacency with a neighboring router with the same VRF?

A. router ospf 1 vrf CCNP network 10.1.1.1 0.0.0.0 area 0 network 10.2.2.2 0.0.0.0 area 0

B. router ospf 1 interface Ethernet1 ip ospf 1 area 0.0.0.0 interface Ethernet2 ip ospf 1 area 0.0.0.0

C. router ospf 1 vrf CCNP interface Ethernet1 ip ospf 1 area 0.0.0.0 interface Ethernet2 ip ospf 1 area 0.0.0.0

D. router ospf 1 vrf CCNP network 10.0.0.0 0.0.255.255 area 0

Which BGP attribute can be used to influence the path that incoming traffic takes into your AS from other Autonomous Systems?

A. Metric manipulation

B. AS_Path

C. Weight

D. Local Preference

How does MPLS Layer 3 VPN function?

A. When an EIGRP internal route is redistributed into BGP by one PE and then back into EIGRP by another PE, the originating router ID for the route is changed to the router ID of the first P

B. When a destination PE device receives a labeled packet, it pops the label and uses it to forward the packet to the correct CE device.

C. When a PE device forwards a packet received from a CE device across the provider network, it labels the packet with the label learned from the source PE device.

D. When a VPN route is learned from a CE device and injected into IGP, a VPN route distinguisher attribute is associated with it.

Refer to the exhibit. An enterprise operations team must monitor all application server traffic in the data center. The team finds that traffic coming from the hub site from R3 and R6 is monitored successfully, but traffic destined to the application server is not monitored. Which action resolves the issue?

A. R4(config)#int gigabitEthernet 1/0R4(config-if)#ip flow ingress

B. R3(config)#int gigabitEthernet 0/0R3(config-if)#ip flow egress

C. R4(config)#int gigabitEthernet 2/0R4(config-if)#ip flow egress

D. R1(config)#int gigabitEthernet 0/0R1(config-if)#ip flow egress

Refer to the exhibits. Phase-3 tunnels cannot be established between spoke-to-spoke in DMVPN.
Which two commands are missing? (Choose two.)

A. The ip nhrp redirect command is missing on the spoke routers.

B. The ip nhrp shortcut command is missing on the spoke routers.

C. The ip nhrp redirect command is missing on the hub router.

D. The ip nhrp shortcut command is missing on the hub router.

E. The ip nhrp map command is missing on the hub router.

Refer to the exhibit. An engineer implemented CoPP but did not see OSPF traffic going through it. Which configuration resolves the issue?

A. control-plane service-policy input COPP

B. policy-map COPP class OSFP police 8000 conform-action transmit exceed-action transmit violate-action drop

C. ip access-list extended OSFP permit ospf any any

D. class-map match-all OSFP match access-group name OSFP

Refer to the exhibits. An engineer investigates a routing issue on R1 and finds that traffic destined to 5.5.5.0/24 does not take all of the paths.
Which action resolves the issue?

A. Increase the variance value in EIGRP.

B. Decrease the variance value in EIGRP.

C. Remove the adjacency of R3 from EIGRP.

D. Stop advertising 192.168.13.0/24 in EIGRP.

20mechanism%20to,means%20equal%2Dcost%20load%20balancing

Refer to the exhibit. An engineer has configured R1 as EIGRP stub router. After the configuration, router R3 failed to reach to R2 loopback address.
Which action advertises R2 loopback back into the R3 routing table?

A. Add a static route for R2 loopback address in R1 and redistribute it to advertise to R3.

B. Use a leak map on R1 that matches the required prefix and apply it with the distribute list command toward R3.

C. Use a leak map on R3 that matches the required prefix and apply it with the EIGRP stub feature.

D. Add a static null route for R2 loopback address in R1 and redistribute it to advertise to R3.

Refer to the exhibit. The network administrator configured redistribution on an ASBR to reach to all WAN networks but failed.
Which action resolves the issue?

A. The route map EIGRP->OSPF must have the 10.0.106.0/24 entry to exist in one of the three prefix lists to pass

B. EIGRP must redistribute the 10.0.106.0/24 route instead of using the network statement

C. The OSPF process must have a metric when redistributing prefixes from EIGRP

D. The route map must have the keyword prefix-list to evaluate the prefix list entries D

How is a preshared key "Test" for all the remote VPN routers configured in a DMVPN using GRE over IPsec set up?

A. authentication pre-share Test address 0.0.0.0 0.0.0.0

B. set pre-share Test address 0.0.0.0 0.0.0.0

C. crypto ipsec key Test address 0.0.0.0 0.0.0.0

D. crypto isakmp key Test address 0.0.0.0 0.0.0.0

The network administrator deployed the Binding Table Recovery feature. Which two devices recover the missing binding table entries? (Choose two.)

A. DHCP client

B. destination host

C. DHCP relay agent

D. source host

E. DHCP server

What is a function of the IPv6 DHCP Guard feature for DHCP messages?

A. If the device is configured as a DHCP server, no message is switched.

B. All client messages are always switched regardless of the device role.

C. It blocks only DHCP request messages.

D. Only access lists are supported for matching traffic.

Refer to the exhibit. The authentication is not working as desired and the user drops into user-exec mode. Which configuration resolves the issue?

A. aaa new-modelaaa authentication common-id default localaaa authorization exec default local!line vty 0 4login authentication defaultauthorization exec default

B. aaa new-modelaaa authentication login default localaaa authorization priv default 15!line vty 0 4login authentication defaultauthorization exec priv15

C. aaa new-modelaaa authentication login localaaa authorization exec local!line vty 0 4login authentication localauthorization exec default

D. aaa new-modelaaa authentication login default localaaa authorization exec default local!line vty 0 4login authentication defaultauthorization exec default

Refer to the exhibit. Which configuration resolves the issue?

A.

B.

C.

D.

Which configuration enables the VRF that is labeled `Inet` on FastEthernet0/0?

A. R1(config)# ip vrf Inet R1(config-vrf)#ip vrf FastEthernet0/0

B. R1(config)#ip vrf Inet FastEthernet0/0

C. R1(config)# ip vrf Inet R1(config-vrf)#interface FastEthernet0/0 R1(config-if)#ip vrf forwarding Inet

D. R1(config)#router ospf 1 vrf Inet R1(config-router)#ip vrf forwarding FastEthernet0/0

Refer to the exhibit.

An engineer is troubleshooting failed access by contractors to the business application server via Telnet or HTTP during the weekend.
Which configuration resolves the issue?

A. R1 no access-list 101 permit tcp 10.3.3.0 0.0.0.255 host 10.1.1.3 eq telnet time-range Contractor

B. R1 time-range Contractor no periodic weekdays 8:00 to 16:30 periodic daily 8:00 to 16:30

C. R4 time-range Contractor no periodic weekdays 17:00 to 23:59 periodic daily 8:00 to 16:30

D. R4 no access-list 101 permit tcp 10.3.3.0 0.0.0.255 host 10.1.1.3 eq telnet time-range Contractor

Refer to the exhibit. The engineer configured and connected Router2 to Router1. The link came up but could not establish a Telnet connection to Router1 IPv6 address of 2001:DB8::1.
Which configuration allows Router2 to establish a Telnet connection to Router1?

A. ipv6 unicast-routing

B. permit ICMPv6 on access list INGRESS for Router2 to obtain IPv6 address

C. permit ip any any on access list EGRESS2 on Router1

D. IPv6 address on GigabitEthernet0/0

Refer to the exhibit. An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command xes the issue?

A. R1(config)# ip route 0.0.0.0 0.0.0.0 2.2.2.2 10 track 1

B. R1(config}# ip route 0.0.0.0 0.0.0.0 2.2.2.2

C. R1(config)# ip sla track 1

D. R1(config)# ip route 0.0.0.0 0.0.0.0 1.1.1.1 track 1

An engineer configured a DHCP server for Cisco IP phones to download its configuration from a TFTP server, but the IP phones failed to load the configuration.
What must be configured to resolve the issue?

A. BOOTP port 67

B. DHCP option 66

C. BOOTP port 68

D. DHCP option 69

Refer to the exhibit. An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0/24 on R2 and R3. The R3 prefix of 10.1.3.0/24 is not received on R2, and the R2 prefix 10.1.2.0/24 is not received on R3. Which action resolves the issue?

A. Split horizon prevents the routes from being advertised between spoke routers. It should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1.

B. There is no spoke-to-spoke connection. DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed by use of the show ip eigrp neighbor command.

C. There is no spoke-to-spoke connection. DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command.

D. Split horizon prevents the routes from being advertised between spoke routers. It should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1.

Router R1 has been configured with a default route like this:
R1#(config) ip route 0.0.0.0 0.0.0.0 10.2.3.1
You want to redistribute this route into OSPF but when you configure the redistribute static command under the OSPF process the default route is not present. What will create a default route in the OSPF routing process?

A. Use the redistribute static subnets command.

B. Create a default metric for the static default route.

C. Use the default-information originate command under the OSPF process.

D. Change the static default route to use an Administrative Distance (AD) greater than 110.

Refer to the exhibit. An administrator is attempting to disable the automatic logout after a period of inactivity. After logging out, the console stopped responding to all keyboard inputs. Remote access through SSH still works.
Which action resolves the issue?

A. configure the no exec-timeout command on line con 0.

B. configure the absolute-timeout command on line con 0.

C. configure the exec command on line con 0.

D. configure the default exec-timeout command on line con 0