Which four options are important points within the Cisco UCS design? (Choose four.)

A. preferred MAC address format

B. preferred guest operating systems

C. DNS configuration

D. preferred WWPN format

E. service profile naming conventions

F. preferred backup strategy

G. Cisco IMC IP addressing range

H. ESX host IP addressing

Which action must occur before an N Port can exchange data with other N Ports?

A. The N Port must log in to its target F Port.

B. The N Port must log in to its attached F Port.

C. The F Port must log in to its target N Port.

D. The F Port must log in to its attached F Port.

Which statement about FCoE is true?

A. FCoE is not supported on any Nexus 2000 Series Fabric Extenders.

B. Not a single FCoE VLAN can map to multiple VSANs.

C. Inter-switch FCoE links can be configured to carry multiple VSANs.

D. FCoE does not support NPV/NPIV mode.

You have a Cisco UCS Fabric Interconnect that connects to upstream switches via four 10-Gbps port channels. You have a fully populated Cisco UCS B-Series
Blade Server chassis that has a UCS-IOM-2208XP installed and uses all of the ports for the blade servers. What is the oversubscription ratio between the chassis and the upstream switch?

A. 6:1

B. 3:1

C. 2:1

D. 4:1

Which innovation in the Cisco NX-OS Software brings an entirely new Layer 2 data plane by encapsulating the frames entering the device with a header that consists of a routable source and destination address?

A. OTV

B. MPLS

C. Routing

D. RSTP

E. LISP

Which use case requires a design that contains multiple VRF instances in a VDC?

A. Provide VRF-aware services to all Layer 3 interfaces.

B. Provide a route policy for incoming packets.

C. Provide routing updates between Layer 3 interfaces.

D. Provide Layer 3 isolation within a VDC.

Refer to the exhibit.
 
Link 1 handles most of the traffic. Which action do you take to load balance traffic evenly between the server and the SAN?

A. Enable src-dst-ox-id load balancing on the MDS switches

B. Enable src-dst-id load balancing on the MDS switches

C. Change the MDS port-channel configuration to source-dest-port

D. Upgrade the bandwidth for the devices connected to the MDS

In a three-tier SAN topology, which network layer should you connect the SAN initiators to?

A. storage edge

B. core

C. host edge

D. distribution

Which Cisco product meets the LAN extension cryptography requirement in OTV over Dark Fiber scenario?

A. IronPort

B. Cisco TrustSec

C. VSG

D. Zone-Based Firewall

Which NHRP features active and standby virtual gateways?

A. GLBP

B. VRRP

C. HSRP

D. SSO

E. NSF

DRAG DROP -
Drag the solution on the left to the appropriate business requirement on the right, such that the solution solves the requirement.
Select and Place:

You are assessing whether the storage system at a data center meets the needs of a customer.
Which three storage system parameters must you assess? (Choose three.)

A. the storage capacity used by the applications

B. the number of physical CPU cores installed on the storage systems

C. the number of input/output operations per second used by the applications

D. the memory resources used by the storage systems

E. the SAN bandwidth used by the applications

F. the CPU speed and utilization of the storage systems

Which option accurately describes updating vNICs templates?

A. can be used to automate the configuration of STP

B. requires that the same VLANs be enabled on all service profiles and Cisco UCS Fabric Interconnects

C. requires that STP be enabled on all service profiles and Cisco UCS Fabric Interconnects

D. can be used to add or remove VLANs from all of the associated service profiles

Scenario -
Review topology and screenshots, and then answer questions that validate your knowledge of Cisco Nexus Switches.
 
Instructions -
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel.
Review the Exhibit associated with the question.
There are four multiple-choice questions with this task.
Be sure to answer all four questions before selecting the Next button
 
 
Refer to the figure in Exhibit 3. You have configured both pairs of Cisco Nexus 7000 Switches for OTV redundancy between data centers. Which of the following
OTV configuration elements will prevent the Overlay interface from forwarding traffic if it is not configured?

A. restart otv-isis

B. otv stp-synchronization

C. otv site-identifier

D. otv vpn-name

Scenario -
Review topology and screenshots, and then answer questions that validate your knowledge of Cisco Nexus Switches.
 
Instructions -
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel.
Review the Exhibit associated with the question.
There are four multiple-choice questions with this task.
Be sure to answer all four questions before selecting the Next button
 
 
Refer to the figure in Exhibit 3. Which item is uniquely required when OTV is configured to use a Unicast Control Pane?

A. ASM

B. Join Interface

C. Adjacency Server

D. Enable Classical Ethernet MAC learning on Edge Interfaces.

Which three options are features of the Cisco Prime Data Center Network Manager? (Choose three.)

A. SAN inventory

B. security rules and objects views

C. device groups and scoping

D. HTTPS connections to devices

E. authentication services

F. inventory and performance views

Which two options are common switching protocols that are used in the data center? (Choose two.)

A. Frame Relay

B. MPLS

C. Ethernet

D. FDDI

E. APPN/APPI

Which three control plane operations are used by vPC? (Choose three.)

A. ARP cache

B. MAC address learning

C. CGMP snooping

D. LACP

E. BPDUs

Which two items represent features of VM-FEX with Cisco Nexus 5500? (Choose two)

A. Software packet switching

B. Hardware packet switching

C. 802.1 Q

D. VN-Tag (802.1 Qbh)

E. Feature rich

F. Higher performance

You are designing a fabric interconnect and Cisco UCS blade chassis solution for a client. The solution includes two vHBA interfaces per server in the blade chassis.
Which two requirements for the servers to boot successfully are true? (Choose two.)

A. On the server side, the amount of WWPNs must equal to the number of the vHBA interfaces multiplied by two.

B. On the server side, the amount of WWPNs must equal to the number of the vHBA interfaces.

C. On the server side, the amount of WWNNs must equal to the number of the vHBA interfaces.

D. On the server side, each server must be allocated one WWPN.

E. On the server side, each server must be allocated one WWNN.

LISP provides which capability?

A. host connectivity redundancy

B. physical host mobility

C. VM mobility

D. VXLAN mobility

Which statement accurately describes Ethernet switching mode on a Cisco UCS Fabric Interconnect?

A. VTP is enabled on the Fabric Interconnect

B. PVST+ runs on the Fabric Interconnect

C. The uplink ports are placed in a Rapid PVST+ edge trunk state

D. The vNICs can be configured for failover

Which two technologies can be used to minimize routing on the DC Core layer from being compromised? (Choose two.)

A. policy-based routing

B. route peer authentication

C. route filtering

D. route summarization

E. route redistribution

Which three items represent features of Cisco Virtual Port Channels? (Choose three.)

A. Single control plane

B. Dual control planes

C. vPC appears as one switch to downstream switches

D. vPC appears as two switches to downstream switch

E. Etherchannel protocols include Static, LACP

F. channel protocols include Static, PAgP, PAgP+, LACP

You must configure resiliency for Fibre Channel uplink ports on Cisco UCS Fabric Interconnects. Which feature should you configure?

A. an appliance port

B. vPC

C. a port channel

D. a unified storage port

Which two tools are included in Cisco Prime DCNM for SAN? (Choose two.)

A. Device Discovery

B. Cisco Traffic Analyzer

C. Cisco DCNM-LAN server

D. Cisco DCNM-SAN Client

E. Cisco Security Manager

What are two benefits of a service insertion that is mediated through the Cisco APIC instead of the classical Ethernet model? (Choose two.)

A. provides Layer 5 service insertion capability

B. provides Layer 7 service insertion capability

C. provide policies that can manage the network and service appliances

D. can automate the service insertion

E. provides built-in services, such as Cisco ACE Web Application Firewall and ADC

Which two options are benefits of credit-based flow control in a Fibre Channel network? (Choose two.)

A. sends credit to all of the switches in a SAN zone

B. increases the credit limit when the buffer overruns

C. maximizes performance under high loads

D. prevents the loss of frames due to buffer overruns

E. provides automatic buffer scaling under high loads

Which two options decrease when using a Cisco Unified Fabric Topology as compared to an isolated fabric topology? (Choose two.)

A. the number of cables required to connect to the pod

B. the cost of data storage

C. the cost-per-port of the Fibre Channel switches

D. the power consumption of each pod

E. the number of uplinks required on the Fibre Channel director switches

You plan to implement Cisco Nexus 7000 Series switches in a data center. Which two factors must be considered for the implementation? (Choose two.)

A. M-Series modules support FcoE.

B. In storage VDCs, you can have only storage traffic.

C. Each F-Series module that runs FCoE requires an FCoE license.

D. F1-Series and F2-Series modules cannot exist in the same VDC.

E. F3-Series modules lack support for FEX.

In which OTV transport mode must an AED router create multiple copies of each control plan packet?

A. site-to-site

B. unicast-only

C. multicast

D. anycast

Which three descriptions of VDC are true? (Choose three.)

A. The management IP address of each VDC must be on a different subnet.

B. The Cisco Nexus 7000 Series platform allows you to build up to 10 VDCs in a single node.

C. You can provide departments with the ability to administer and maintain their own network nodes.

D. You can secure the network partition between different tenants on the same physical switch.

E. You can perform an ISSU on a per-VDC basis to separate the fault domains.

F. You can consolidate the switch platforms of multiple departments onto a single physical platform.

You are sizing the aggregation layer for a data center. Which two factors influence the size of the TCAM table space on the aggregation data center switches?
(Choose two.)

A. the QoS policies

B. the configured VLANs

C. the configured OSPF networks

D. the configured security access control list policies

E. the configured OSPF processes

You deploy new server infrastructure by using a Cisco UCS platform. Which two design options can you use to increase the redundancy of the new compute solution? (Choose two.)

A. a 10-Gb uplink port

B. a pin vNIC in the server profile to a specific Fabric Interconnect node that has failover disabled

C. an uplink port in a port channel configuration

D. static pinning at the server ports

E. more than one server port to connect the Cisco UCS B-Series blade IOM

Which two business requirements have the most influence on the data center design? (Choose two.)

A. reduce power consumption

B. increase network bandwidth

C. increase storage capacity

D. increase cooling requirement

E. reduce virtual machine to host ratio

F. reduce data center footprint (floorspace)

Which four options describe I/O Accelerator? (Choose four.)

A. is topology dependent

B. provides unified acceleration service

C. provides high availability and resiliency

D. provides load balancing

E. is transport agnostic

F. Each IOA engine provides 1-Gbps application throughput.

G. uses TCP

H. does not support multiple paths and PortChannels

Which two options are goals of virtualization in the data center? (Choose two.)

A. to provide automation for device deployment

B. to provide resource isolation

C. to automate the provisioning of VLANs

D. to provide integration between devices in a heterogeneous network

E. to provide flexible resource management

What introduces unique implications into the overall Data Center aggregation layer design? (Choose three.)

A. High-speed switching fabric with a high forwarding rate

B. Over-subscription values

C. Service Modules

D. IP routing

E. WAN

F. Internet Edge

Refer to the exhibit. Which two descriptions of the purpose of the L1-L2 links between FI A and FI B are true? (Choose two.)

A. synchronizes the configuration information

B. provides a vPC peer link between the fabric interconnects

C. allows each fabric interconnect to monitor the status of the other fabric interconnect continuously

D. provides an alternate data path if an upstream link fails

E. migrates VIFs from FI A to FI B if FI A fails

Which option is an advantage of utilizing hypervisor technology within a Cisco Unified Fabric data center environment?

A. distributed load processing

B. availability of blade versus rack-mountable servers

C. reduced power and cooling requirements

D. integrating the virtual machines into the access layer

Which two types of connections can be used to build data center interconnects via vPC? (Choose two.)

A. company-owned DWDM

B. service provider MPLS

C. service provider IP

D. service provider DWDM

E. service provider VPLS

You have a Cisco UCS B-Series Blade Server chassis connected, which has four 10-Gbps connections to Cisco UCS Fabric Interconnect A. You plan to deploy a blade that has ESXi installed. You must provide a dedicated 10-Gbps uplink to the blade. Which two actions should you perform? (Choose two.)

A. Configure a port channel between the Fabric Interconnect and the IOM.

B. Implement a QoS policy that has a policy bandwidth and assign the policy to a server profile.

C. Configure static pining to the uplink port in the server profile.

D. Configure dynamic pinning to the uplink port in the server profile.

E. Configure a vPC between the Fabric Interconnect and the IOM.

Which three actions must you perform to implement Cisco FabricPath on a data center network? (Choose three.)

A. Configure the VLAN in FabricPath mode.

B. Configure the interface to use the STP type of normal.

C. Configure the interfaces in FabricPath mode.

D. Configure the interfaces in trunk mode.

E. Enable the IS-IS feature.

F. Install the FabricPath feature set.

Which statement about VLANs configured in FabricPath mode on a Cisco Nexus 7000 switch is true?

A. They use classical MAC learning by default.

B. FabricPath VLANs requires 802.1Q trunks for forwarding.

C. VLANs configured for FabricPath can exist only on F-Series line cards.

D. The forwarding engine uses any M-Series line cards present in the switch for MAC proxy forwarding.

You use Cisco UCS Central to manage Cisco UCS. Which statement accurately describes how local and global policies are applied?

A. A local policy is applied by using Cisco UCS Central, and a global policy is applied by using Cisco UCS Director.

B. A local policy is applied by using Cisco UCS Manager, and a global policy is applied by using Cisco UCS Central.

C. A local policy is applied by using Cisco UCS Director, and a global policy is applied by using Cisco UCS Central.

D. A local policy is applied by using Cisco UCS Central, and a global policy is applied by using Cisco UCS Manager.

Which two options are reasons to use IP routing to segment a data center instead of Layer 2 routing? (Choose two.)

A. Spanning Tree Protocol

B. simplify design

C. broadcast flooding

D. ease of routing protocol configuration

E. cost

Which statement describes an interconnect link between an FCoE NPV switch and an FCF switch?

A. The interconnect must use port type NP on the FCoE switch.

B. The interconnect must use port type VNP on the FCoE switch.

C. The interconnect must use port type E on the FCoE switch.

D. The FCoE switch must create the tunnel interface and bind to the physical interconnect.

Refer to the exhibit.
Which four options are Cisco best practices that should be included or implemented in the design for resiliency, deterministic behavior, and fast convergence in case of link failures? (Choose four.)

A. Add additional OSPF adjacency between N7K-1 and N7K-2 via dedicated Layer 3 link.

B. Configure vPC peer-gateway in the vPC domain between N7K-1 and N7K-2.

C. Use point-to-point OSPF adjacencies.

D. Place the primary FHRP role on N7K-1.

E. Configure Layer 3 port channels between all N7K devices.

F. N7K-3 and N7K-4 must be the OSPF designated routers.

G. Place the primary FHRP role on N7K-2.

H. All OSPF adjacencies should be between loopback interfaces.

Which component of a Cisco Nexus 1000V Series switch is responsible for propagating configurations to virtual switches?

A. SUP

B. FEX

C. VSM

D. VEM

What is the default CoS value for FCoE packets on a storage VDC?

A. 1

B. 2

C. 3

D. 5

E. 7