350-801 Mock Test Free – 50 Realistic Questions to Prepare with Confidence.
Getting ready for your 350-801 certification exam? Start your preparation the smart way with our 350-801 Mock Test Free – a carefully crafted set of 50 realistic, exam-style questions to help you practice effectively and boost your confidence.
Using a mock test free for 350-801 exam is one of the best ways to:
- Familiarize yourself with the actual exam format and question style
- Identify areas where you need more review
- Strengthen your time management and test-taking strategy
Below, you will find 50 free questions from our 350-801 Mock Test Free resource. These questions are structured to reflect the real exam’s difficulty and content areas, helping you assess your readiness accurately.
An engineer is trying to add a new subscriber to the cluster of Cisco UCM, and the synchronization is failing. The engineer obtained the output from the publisher and noticed the error. Based on the output, what is the issue?A. The NTP server is running out of space in the hard drive, which prevents the cluster service from starting.
B. The NTP service is pointing to the wrong publisher.
C. The NTP server must be replaced by another server with NTP stratum 1, 2, or 3 running version NTPv4.
D. The NTP server for Cisco UCM must be stratum 6 or higher.
Where is the default Interregion Maximum Session Bit Rate for a region configured?A. Service Parameter Configuration
B. Enterprise Phone Configuration
C. Enterprise Parameters Configuration
D. Region Configuration
Where would an administrator update learned patterns from the DNA UI?A. System —> Enterprise parameters
B. Service —> Control Center —> DNA
C. Service —> Control Center
D. System —> Service Parameters
Which location must be assigned to the SIP trunk to replicate enhanced location information via a SIP trunk?A. hub_none
B. replica
C. phantom
D. shadow
An engineer must manually provision a Cisco IP Phone 8845 using SIP. Which two fields must be configured for a successful provision? (Choose two.)A. location
B. media resources group list
C. SIP profile
D. CSS
E. device security profile
A collaboration engineer troubleshoots issues with a Cisco IP Phone 7800 Series. The IPv4 address of the phone is reachable via ICMP and HTTP, and the phone is registered to Cisco UCM. However, the engineer cannot reach the CLI of the phone. Which two actions in Cisco UCM resolve the issue? (Choose two.)A. Enable Settings Access under Product Specific Configuration Layout in Cisco UCM.
B. Enable FIPS Mode under Product Specific Configuration Layout in Cisco UCM.
C. Enable SSH Access under Product Specific Configuration Layout in Cisco UCM.
D. Set a username and password under Secure Shell Information in Cisco UCM.
E. Disable Web Access under Product Specific Configuration Layout in Cisco UCM.
Which configuration step is necessary for a Cisco SIP phone to synchronize its time with a specific source?A. Add a Phone NTP Reference to the Date/Time Group.
B. Assign the device to the correct region.
C. Change the Time Format from 24-hour to 12-hour.
D. Change the Time Zone from ג€America/Los_Angeles" to ג€Etc/GMT+8".
Refer to the exhibit.
There is a call flow between Phone A and Phone B. Phone B (holder) places Phone A (holdee) on hold. Which MRGL and Audio Source are played to Phone A?A. MRGL A and Audio Source 4
B. MRGL B and Audio Source 2
C. MRGL B and Audio Source 4
D. MRGL A and Audio Source 2
An engineer is configuring a PRI card on a Cisco ISR 4300 Series Router. When the engineer configures the voice PRI on the router, this error is received: "T1 0/1/0: No DSP resources to configure voice feature". Which action must the engineer take to resolve the issue if a PVDM card was installed in the motherboard?A. Install the NIM card on a different slot.
B. Replace the memory slot in the motherboard.
C. Replace the flashcard, restart the router, and try it again.
D. Install the PVDM directly to the NIM card.
Configuration of DNS is required to achieve a fully functional Cisco UCM system. Cisco UCM uses DNS to resolve fully qualified domain names to IP addresses for which destinations?A. MRA
B. trunk
C. AAR
D. H.323
An administrator is configuring LDAP for Cisco UCM with Active Directory integration. A customer has requested to use `ipphone` instead of `telephoneNumber' as the phone number attribute. Where does the administrator specify this attribute mapping in Cisco UCM?A. LDAP Custom Filter
B. LDAP Authentication
C. LDAP Directory user fields
D. LDAP Directory custom user fields
Which type of greeting in the Call Handler configuration in Cisco Unity Connection overrides all other greetings?A. supervisory
B. alternate
C. holiday
D. priority
How can an engineer determine location-based CAC bandwidth requirements for Cisco Unified Communications Manager?A. Set the requirements in the service parameters.
B. Add the requirements for each audio and video codec and multiply how many calls must be supported.
C. Execute the Resource Reservation Protocol to return location-based requirements.
D. Calculate the number of calls against the license for Cisco Unified Border Element to determine calls per location.
A Cisco Unity Connection Administrator must set a voice mailbox so that it can be accessed from a secondary device. Which configuration on the voice mailbox makes this change?A. Attempt Forward routing rule
B. Alternate Extensions
C. Alternate Names
D. Mobile User
Refer to the exhibit. What is the registration state of the analog port in this debug output?A. The analog port is currently shut down.
B. The analog port is registered to Cisco UCM.
C. The MGCP Gateway is not communicating with the Cisco UCM.
D. The analog port failed to register to Cisco UCM with an error code 200.
Refer to the exhibit. A customer submits this debug output, captured on a Cisco IOS router. Assuming that an MGCP gateway is configured with an ISDN BRI interface, which BRI changes resolve the issue?A. interface BRI0/1/1 no ip address isdn switch-type basic-net3 isdn incoming-voice voice isdn send-alerting isdn static-tei 0
B. interface BRI0/1/0 no ip address isdn switch-type basic-net3 isdn point-to-multipoint-setup isdn incoming-voice voice isdn send-alerting isdn static-tei 0
C. interface BRI0/1/1 no ip address isdn switch-type basic-net3 isdn point-to-point-setup isdn incoming-voice voice isdn send-alerting isdn static-tei 0
D. interface BRI0/1/1 no ip address isdn switch-type basic-net3 isdn point-to-multipoint-setup isdn incoming-voice voice isdn send-alerting isdn static-tei 0
Refer to the exhibit. A call is failing to establish between two SIP Devices. The called device answers with this SDP. Which SDP parameter causes this issue?A. The payload for G.711ulaw must be 18.
B. The calling device did not offer a ptime value.
C. The media stream is set to sendonly.
D. The RTP port is set to 0.
What is a valid class included in the 8-Class QoS Strategy in a VoIP network?A. Assured Forwarding
B. Broadcast Video
C. Multimedia Conferencing
D. Real-Time Interactive
End users report bad video quality and voice choppiness on Cisco Collaboration endpoints. The engineer changed the device pool the users were in but did not correct the problem. Which action should be taken to troubleshoot this issue?A. Restart the Cisco Location Bandwidth Manager service on the Cisco UCM publisher
B. Check for duplex/speed mismatches between the network port settings of the system and network switch
C. Use direct IP address calls between two endpoints to troubleshoot call quality issues
D. Set the service parameter Use Video Bandwidth Pool for Immersive Video Calls to ג€falseג€
What happens when a Cisco IP phone loses connectivity to the cluster during an active call?A. The call drops immediately.
B. The call drops after missing two keepalives from Cisco UCM.
C. The call continues to be active, but features like transfer or hold do not work.
D. The call continues and all features work.
A presence redundancy group is deployed, and an engineer initiates a manual fallback. Which statement about Cisco Server Recovery Manager is true?A. disconnects all users that had been failed over, and the users must log in again
B. disconnects all users that had been failed over
C. restarts critical services on the secondary node
D. restarts the Cisco Presence Engine
On a Cisco Catalyst Switch, which command is required to send CDP packets on a switch port that configures a Cisco IP phone to transmit voice traffic in 802.1Q frames, tagged with the voice VLAN ID 221?A. Device(config-if)# switchport trunk allowed vlan 221
B. Device(config-if)# switchport vlan voice 221
C. Device(config-if)# switchport voice vlan 221
D. Device(config-if)# switchport access vlan 221
What is the purpose of using an Expressway-C and Expressway-E pair in Cisco Collaboration Edge preferred architecture?A. to provide internet connectivity and firewall traversal for voice and video
B. to block access to ports 5060 and 5061
C. to allow access on internal devices for management
D. to provide internet connectivity via PSTN router
Which two parameters influence the total number of supported conference participants on a Cisco IOS XE router that has DSP modules? (Choose two.)A. voice codec
B. software version of the router
C. license types
D. session capacity of the PVDM module
E. number of protocol data units
Due to provider requirements, outgoing calls from the Enterprise to the PSTN must start with channel 1.
Which ISDN command changes the channel selection on IOS to meet this requirement?A. isdn bchan-number-order descending
B. isdn bchan-number-order ascending
C. isdn protocol-emulate network
D. isdn incoming-voice voice
Refer to the exhibit. When a UC Administrator is troubleshooting DTMF negotiated by this SIP INVITE, which two messages should be examined next to further troubleshoot the issue? (Choose two.)A. REGISTER
B. UPDATE
C. PRACK
D. NOTIFY
E. SUBSCRIBE
What are two functions of a dial-plan? (Choose two.)A. call recording
B. endpoint features
C. calling privileges
D. digit manipulation
E. ring cadence
What is a characteristic of a SIP endpoint configured in Cisco UCM with "Use Trusted Relay Point" set to "On"?A. It enables Cisco UCM to insert an MTP or transcoder designated as a TRP.
B. It enables the Use Trusted Relay Point setting from the associated common device configuration.
C. If TRP is allocated and MTP is also required for the endpoint, calls fail.
D. It creates a trust relationship with the called party.
An engineer must configure a route pattern that can route all +E.164 globalized international numbers for the dial plans of all countries. Which Cisco UCM configuration accomplishes this task?
A.
B.
C.
D.
Refer to the exhibit. An engineer is troubleshooting a codec negotiation issue where both endpoints that are involved in the call support the codecs listed in the exhibit. Which audio codec is selected if a call between two endpoints in Region1 is placed?A. G.722
B. G.729
C. G.711a
D. G.711u
An administrator would like to set several Cisco Jabber configuration parameters to only apply to mobile clients (iOS and Android). How does the administrator accomplish this with Cisco Jabber 12.9 and Cisco UCM 12.5?A. Create a user profile in Jabber Policies
B. Deploy jabber-config-user.xml on iOS and Android devices
C. Assign the desired configuration file to ג€Mobileג€ Jabber Client Configuration in the Service Profile
D. Upload the jabber-config.enc file to TFTP
An engineer is configuring a Cisco Unified Border Element to allow the video endpoints to negotiate without the Cisco Unified Border Element interfering in the process. What should the engineer configure on the Cisco Unified Border Element to support this process?A. Configure codec transparent on the dial peers.
B. Configure a transcoder for video protocols.
C. Configure a hardcoded codec on the dial peers.
D. Configure pass-thru content sdp on the voice service.
Where is urgent priority enabled to bypass the T302 timer?A. transformation pattern
B. directory number
C. route partition
D. CTI port
A customer enters no ip domain lookup on the Cisco IOS XE gateway to suppress the interpreting of invalid commands as hostnames. Which command is needed to restore DNS SRV or A record resolutions?A. ip domain lookup
B. ip dhcp pool
C. ip dhcp excluded-address
D. ip dhcp-sip
A Cisco UCM administrator wants to enable the Self-Provisioning feature for end users. Which two prerequisites must be met first? (Choose two.)A. End users must have a primary extension.
B. End users must be associated to a user profile or feature group template that includes a universal line template and universal device template.
C. End users must have a secondary extension.
D. End users must belong to Standard CCM Admin Users group, the Standard CCM End Users group, and the Standard CCM Self-Provisioning group.
E. Cisco Extended Functions service must be running.
An organization is deploying a Cisco Unified Border Element for Webex calling. The engineer's voice gateway is a Cisco CSR1000v on version 17.x.x. How must the engineer configure G.729 codec to be the first priority for all calls, followed by G.711ulaw and G.711alaw?A.
B.
C.
D.
An engineer must deploy the Cisco Webex app to a shared Windows Virtual Desktop Infrastructure environment in the C:Program Files folder. Which command line argument must be run when running the installer?A. ALLUSERS=1
B. ENABLEVDI=2
C. ROAMINGENABLED=1
D. INSTYALLWV2=1
Which Cisco Unified Communications Manager service parameter should be enabled disconnect a multiparty call when the call initiator hangs up?A. Drop Ad Hoc Conference
B. H.225 Block Setup Destination
C. Block OffNet To OffNet Transfer
D. Enterprise Feature Access Code for Conference
How are network devices monitored in a collaboration network?A. System logs are collected in a Cisco Prime Collaboration Server.
B. Ping Sweep reports ג€unmanagedג€ state devices.
C. The Cisco Discovery Protocol table is shared among devices.
D. Simple Network Managed Protocol is enabled on each device to poll specific values periodically.
An administrator must implement toll fraud prevention on Cisco UCM using these parameters:
✑ Enable Forced Authorization Code 112211.
✑ Set an authorization level of 3 for the route pattern 8005551212.
✑ Require no access code to dial 10-digit numbers.
How must the route pattern be implemented?A. Pattern = 8005xxxxxx
B. Pattern = 1122113.8005551212
C. Pattern = 3.800xxxxxxx
D. Pattern = 8005551212.1122113
Refer to the exhibit. An engineer must deploy a Cisco Unified Border Element that will allow the last four digits of a dialed number to be sent from the Cisco Unified Border Element to Cisco UCM. The configuration in the exhibit already exists on die Cisco Unified Border Element. Which additional configuration must be performed on the Cisco Unified Border Element?A.
B.
C.
D.
An administrator configures international calling on a Cisco UCM cluster and wants to minimize the number of route patterns that are needed. Which route pattern enables the administrator to match variable-length numbers?A. 9.011@
B. 9.011#
C. 9.011*
D. 9.011!
Refer to the exhibit. A Cisco UCM user with directory number 4401 dials 5507, and the call is routed to a Cisco Unified Border Element. Which IP address will the call be sent to?A. 10.0.0.2
B. 10.0.0.3
C. 10.0.0.4
D. 10.0.0.1
How does Cisco Unified Communications Manager perform a digit analysis on-hook versus off-hook for an outbound call from a Cisco IP phone that is registered to Cisco Unified CM?A. On-hook, Unified CM performs a digit-by-digit analysis; off-hook, Unified CM considers all digits were dialed and does not wait for additional digits.
B. On-hook, Unified CM considers all digits were dialed and does not wait for additional digits; off-hook, Unified CM performs a digit-by-digit analysis.
C. On-hook, by pressing the digits and entering "#" to process the call, Unified CM performs a digit-by-digit analysis; off-hook, Unified CM analyzes all digits as a string.
D. On-hook, no digit analysis is performed; off-hook, Unified CM requires the ג€#* to start the digit analysis.
By default, IP phones upgrade their images using the HTTP Service from the TFTP Server integrated into one or more of the call processing platforms. Which Port / Transport Protocol does this service use?A. 6970 / UDP
B. 443 / TCP
C. 6970 / TCP
D. 8080 / TCP
Refer to the exhibit.
A collaboration engineer needs to replace the original, single NTP server that was configured during the initial install of a Cisco UCM server. What is the first step to accomplish this task?A. Stop the NTP service on Cisco UCM.
B. Enable NTP authentication for the new NTP server on Cisco UCM.
C. Restart the NTP service on Cisco UCM.
D. Delete the original NTP server from Cisco UCM.
A remote office has a less-than-optimal WAN connection and experiences packet loss, delay, and jitter. Which VoIP codec should be used in this situation?A. G.711alaw
B. iLBC
C. G.722.1
D. G.729A
An administrator needs to create a partial PRI consisting of the first seven timeslots available. Which configuration snippet configures the ISDN E1 PRI for this task?A. config t 2900(config)#isdn switch-type primary-ni 2900(config)#pri-group timeslots 1-7
B. config t 2900(config)#isdn switch-type primary-ni 2900(config)#controller e1 0/0/0 2900(config-controller)#pri-group timeslots 1-7
C. config t 2900(config)#isdn switch-type primary-ni 2900(config)#interface Serial0/0/0:15 2900(config-controller)#pri-group timeslots 1-7
D. config t 2900(config)#isdn switch-type primary-ni 2900(config)#controller e1 0/0/0 2900(config-controller)#pri-timeslots 1-7
A company's employees have been complaining that they have been unable to select options on the internal IVR of the help desk. IT support has been given
Cisco UCM traces and below is the snippet of the SDP of the INVITE packet. m=audio 25268 RTP/AVP 18 101 a=rtpmap:0 PCMU/8000 a=rtpmap:18 G729/8000 a=ptime:20 a=fmtp:18 annexb=no a=rtpmap:101 telephone-event/8000 a=fmtp:101 0-15
How is this issue resolved?A. Configure DTMF for KPML.
B. Configure CODEC for G.729.
C. Configure DTMF for RFC 2833.
D. Configure CODEC for G.722.
An engineer with ID012345678 must build an international dial plan in Cisco Unified Communications Manager. Which action should be taken when building a variable-length route pattern?A. reduce the T302 timer to less than 4 seconds
B. configure single route pattern for international calls
C. create a second route pattern followed by the # wildcard
D. set up all international route patterns to 0.!
Access Full 350-801 Mock Test Free
Want a full-length mock test experience? Click here to unlock the complete 350-801 Mock Test Free set and get access to hundreds of additional practice questions covering all key topics.
We regularly update our question sets to stay aligned with the latest exam objectives—so check back often for fresh content!
Start practicing with our 350-801 mock test free today—and take a major step toward exam success!