A company is using Cisco Jabber on-premises to make B2B calls on video. The calls are using Cisco Expressway-C and Expressway-E and have been configured in Cisco UCM to be able to call any URI on the internet. The Jabber client also has voice enabled and must be able to call local, regional, and international numbers.
Where must Cisco UCM be configured to meet this requirement for URI dialing?

A. Enter “!#” in the SIP route pattern.

B. Enter “.*” in the route pattern section tied to a route group and list.

C. Enter “*” in the SIP route pattern.

D. Enter “!#” in the route pattern section tied to a route group and list.

Refer to the exhibit. An administrator just upgraded to Cisco UCM to version 14 and started SIP implementation with some new SIP trunks. During the testing, an error was reported when making a call. Which action resolves the issue?

A. Make sure the destination number is configured correctly and the device is registered.

B. Disable SIP Rel1XX Options.

C. Change DTMF Signaling Method to “RFC 4833”.

D. Change to a valid range.

Refer to the exhibit. An administrator is trying to test outbound calls toward the ITSP but cannot complete the call and receives a SIP error. ITSP is consulted, and the issue is that the ANI that is being sent is not the DID provided 8005532447. Which configuration change sends the correct ANI on the INVITE sent to ITSP to fix the error?

A. voice class sip-profiles 2request INVITE sip-header To modify “sip:(.*)@” sip:8005532447@

B. voice translation-rule 3rule 1/.*/ /8005532447/

C. voice class sip-profiles 1request INVITE sip-header Diversion modify “sip:(.*)@” “sip:8005532447@”

D. voice translation-rule 4rule 1/^.*(8005532447)/ /1/

An engineer has temporarily disabled toll fraud prevention for SIP line calls on a Cisco CME12.6x and must enforce security and toll fraud prevention for the SIP line side on Cisco Unified CME. Which configuration must be used to start this process?

A. voice service voipenable ip address trust list

B. voice service voipip address trusted list

C. voice service voipip address trusted authenticate

D. voice service voipenable ip address trust authentication

A company has an SRST gateway running an IOS XE image. The company plans to enable the IPv6 addressing companywide. To enable the IPv6 in a unified
SRST gateway to support SIP phones, what are two supported supplementary features for an IPv6 fallback scenario? (Choose two.)

A. three-way conference

B. secure SIP lines

C. T.38 fax relay

D. transcoding

E. SIP trunk

Refer to the exhibit. A collaboration engineer is troubleshooting an issue where the PSTN calls of a Cisco UCM IP phone user are not reaching the PSTN gateway. Which action resolves the issue?

A. Change the calling search space of the user’s line or device.

B. Change the “Call Classification” to “OnNet” on the route pattern.

C. Ensure that the user’s phone is assigned to a device pool with the correct local route settings.

D. Deselect “Block this pattern” on the route pattern.

An engineer must configure call queuing under a Hunt Pilot. After the engineer receives the audio file that will be played to callers during queuing, which two steps should be taken to complete the configuration? (Choose two.)

A. Assign the uploaded audio file to “Network Hold MOH Source & Announcements” under Hunt Pilot’s Queuing section.

B. Upload the audio file in “TFTP File Management” via OS Administration GUI.

C. Assign the uploaded audio file to the hunting Line Group member’s “User Hold MOH Audio Source”.

D. Assign the uploaded audio file to the hunting Line Group member’s “Network Hold MOH Audio Source”.

E. Upload the audio file in “MOH Audio File Management” via CM Administration GUI.

Why would RTP traffic that is sent from the originating endpoint fail to be received on the far endpoint?

A. The far end connection data (c=) in the SDP was overwritten by deep packet inspection in the call signaling path.

B. Cisco Unified Communications Manager invoked media termination point resources.

C. The RTP traffic is arriving beyond the jitter buffer on the receiving end.

D. A firewall in the media path is blocking TCP ports 16384-32768.

Refer to the exhibit. Which change to the translation rule is needed to strip only the leading 9 from the digit string 9123548?

A. rule 1 /^9(d*)/ /l/

B. rule 1 /^9(.*)/ /l/

C. rule 1 /.*(3548$)/ /l/

D. rule 1 /^9123548/ /1/

An administrator must control the number of calls to a remote specific site to reduce bandwidth constraints. The users on that remote site report bad quality of the calls passing through that WAN link. Which action must the administrator take in Cisco UCM to resolve the issue?

A. Use RSPV.

B. Use Location Bandwidth Manager.

C. Use Expressway deployment.

D. Use Call Allow Controller.

An administrator troubleshoots call failure in a new deployment and finds that the SIP INVITE messages sent to the service provider contain a diversion header with the user's 4-cigit directory number. These 4-digit directory numbers range from 1000 to 9899. The service provider is rejecting the calls because it requires that the diversion header contain 10 digits. Which command on the Cisco Unified Border Element resolves this issue for all users?

A. voice class sip-profiles 105request INVITE sip-header Diversion modify ““

B. voice class sip-profiles 105request INVITE sip-header Diversion modify ““

C. voice class sip-profiles 105request INVITE sip-header Diversion add ““

D. voice class sip-profiles 105request INVITE sip-header Diversion modify ““

Refer to the exhibit. All calls from site A to site B are failing, and the issue has been identified as a media negotiation problem. Which configuration change resolves this issue?

A. Increase the bandwidth allowance between the RTP_Reg and SJ_Reg regions to 64 kbps.

B. Enable Early Offer on the SIP trunk.

C. Create a new audio codec preference list with G.711 U-law 64k as the highest priority and apply it to RTP_Reg and SJ_Reg.

D. Disable G.722 on all devices at both sites.

An engineer must configure a secure SIP trunk with a remote provider, with a specific requirement to use port 5065 for inbound and otubound traffic. Which two items must be configured to complete this configuration? (Choose two.)

A. Incoming Port in SIP Information section of the SIP Trunk configuration.

B. Incoming Port in Security Information of the SIP Profile configuration.

C. Destination Port in SIP Information section of the SIP Trunk configuration

D. Incoming Port in SIP Trunk Security Profile configuration

E. Destination Port in SIP Trunk Security Profile configuration

When locations-based Call Admission Control denies the call, which two masks can AAR apply when routing the call through the PSTN? (Choose two.)

A. AAR destination mask

B. called party transform mask

C. external phone number mask

D. +E.164 alternate number mask

E. enterrise alternate number mask

Cisco SIP IP telephony is implemented on two floors of your company. Afterward, users report intermittent voice issues in calls established between floors. All calls are established, and sometimes they work well, but sometimes there is one-way audio or no audio. You determine that there is a firewall between the floors, and the administrator reports that it is allowing SIP signaling and UDP ports from 20000 to 22000 bidirectionally. What are two possible solutions? (Choose two.)

A. Go to the SIP profile assigned to these IP phones in Cisco Unified CM and change the range of media ports to 16384-32767

B. Ask the firewall administrator to change the ports to TCP.

C. Ask the firewall administrator to change the range of UDP ports to 16384-32767.

D. Go to the SIP profile assigned to these IP phones in Cisco Unified CM and change the range of media ports to 20000-22000.

E. Go to System Parameters in Cisco Unified Communications Manager and change the range of media ports to 20000-22000.

An organization has decided to implement hunt groups to help with the distribution of calls between different members. The administrator must configure hunt groups on Cisco UCM. In the configuration, at which step does an administrator have the option to configure a distribution algorithm (top down, circular, longest idle time, broadcast)?

A. hunt group

B. line group

C. hunt list

D. route list

Some users report poor quality when they travel to another continent and make calls. This issue applies only to one continent and not to others, where typically the dialing is fast and quality is clear. Users experience the same result at home when they call the same numbers in that specific continent. It seems like some users do not exist in the correct PSTN gateway when making calls to a specific country. The company is using TEHO to save on the cost of international or long-distance calling.
They are also using a globalized dial plan. What is the cause of the issue?

A. CUBE is not configured for TEHO in the specific country.

B. A local route group is not added to the route pattern.

C. The users are missing this specific gateway at the device pool level.

D. Regions in Cisco UCM are not configured correctly.

Which two types of authentication are supported for the configuration of Intercluster Lookup Service? (Choose two.)

A. TokenID

B. username and secret key

C. TLS certificates

D. passwords

E. FQDN of the servers defined in DNS

Which configuration element of a hunt group allows for changing Calling Party Transformations settings?

A. line group

B. hunt pilot

C. route group

D. hunt list

An administrator has configured two route patterns, 9.911 and 9.[2-9]XXXXXX. When a user dials 9911. Cisco UCM waits for the T302 timer before routing the call. How will the administrator force interdigit timeout and route the call as soon as the user has finished dialing 9911, without waiting for the T302 timer to expire?

A. decrease the T302 timer in Service Parameters from the default value

B. enable Urgent Priority on the 9.[2-9]XXXXXX pattern

C. enable Urgent Priority on the 9.911 pattern

D. enable Device Override on both route patterns

A solution for a large company is being reconfigured to optimize for cost saving. The company has an extensive global QoS-enabled network with enough bandwidth to create a converged network. Local calls are relatively inexpensive in countries the company have operations, but long distance and international calls are expensive.
Which type of configuration supported by Cisco UCM would help optimize cost control for this company?

A. standard local route groups for mobile users

B. Mobile and Remote Access

C. high complex codec support like G.729 to minimize bandwidth usage

D. tail end hop off

Which IOS command creates a SIP-enabled dial peer?

A. voice dial-peer 20 sip

B. dial-peer voice 20 voip

C. dial-peer voice 20 pots

D. dial peer voice 20 sip

Refer to the exhibit. A user reports that when they call a specific phone number, no one answers the call, but when they call from a mobile phone, the call is answered. The engineer troubleshooting the issue is expecting the far-end gateway to cut through audio on the 183 Session Progress SIP message. Which SIP
Profile configuration element is necessary for the Cisco Unified Communications Manager to send acknowledgement of provisional responses?

A. Allow Passthrough of Configured Line Device Caller Information must be enabled.

B. Accept Audio Codec Preferences in Received Offer must be set to On.

C. On the SIP Profile, the configuration parameter SIP Rel1XX Options must be set to Send PRACK for all 1xx Messages.

D. Early Offer for G Clear Calls must be enabled.

Calls are not working when sent from a Cisco Unified Border Element to a service provider. After investigating the logs, the engineer notes that the Cisco Unified Border Element is sending the extension only. How is the issue addressed in the configuration?

A. voice class request sip-header diversion

B. sip-header contact modify

C. voice class request sip-header modify

D. request invite sip-header diversion modify

Refer to the exhibit. A company needs to ensure that all calls are normalized to + E164 format. Which configuration will ensure that the resulting digit string +14085554001 is created and will be routed to the E.164 routing schema?

A. Calling Party Transformation Mask of +14085554XXX

B. Calling Party Transformation Mask of +1408555XXXX

C. Called Party Transformation Mask of +1408555[35]XXX

D. Called Party Transformation Mask of +14085554XXX

A customer reports audio quality issues between video endpoints in the HQ location in California and one of the branches in Texas. Which two actions must RTCP take to troubleshoot this issue? (Choose two.)

A. Allow for VAD to be used for calls using the G7.29 codec, which reduces the usage of the WAN bandwidth and saves around 30% of bandwidth per call

B. Configure the rtcp keepalive command in Cisco Unified Border Element to generate reports, which can be reviewed using the debug voip rtcp packet command.

C. Encrypt the media to stop rogue devices from replying and putting that traffic back on the WAN, which avoids any extra bandwidth and ensures the quality of the calls.

D. Gather statistics on a media connection and information such as packets sent, lost packets, jitter, feedback, and round-trip delay. This information can help isolate the type of audio quality issues and the direction of the affected traffic.D. Compress the headers of RTP traffic to lower the bandwidth consumption over the WAN, which allows more calls with less bandwidth consumed.

Refer to the exhibit. An engineer is trying to set up a new deployment using the SIP provider with TCP for signaling. After troubleshooting, the customer notices that the matching incoming dial peer and outgoing dial peer did not generate the INVITE to the SIP provider. Why is the call failing?

A. The ITSP is sending FIN.

B. The ITSP is not sending the ACK.

C. The ITSP is sending CLOSE state.

D. The ITSP is not answering the SYN.

Configure Call Queuing in Cisco Unified Communications Manager. Where do you set the maximum number of callers in the queue?

A. in the telephony service configuration

B. in the queuing configuration

C. in Cisco Unified CM Enterprise Parameters

D. in Cisco Unified CM Service Parameters

An administrator is configuring a cluster for ILS and wants to limit the amount of entities that Cisco Unified Communications Manager can write to the database for data that is learned through ILS. Which service parameter is used to adjust this limit?

A. ILS Max Number of Learned Objects in Database

B. ILS Active Learned Object Upper Limit

C. Global Data Service Parameter Limit

D. Imported Dial Plan Replication Database Object Lower Limit

Where is the dtmf-relay command configured on Cisco Unified Border Element?

A. in the voice-class VoIP configuration

B. in the VoIP dial peer

C. in global SIP configuration

D. in the VoIP or POTS dial peers

What does VoIP trace in a Cisco Unified Border Element do?

A. It stores all call trace data in system log files for successful and failed calls.

B. It stores all call trace data in system file logs for failed calls.

C. It stores all call trace data in system memory for failed calls.

D. It stores all call trace data in system memory for successful and failed calls.

Refer to the exhibit. An administrator just implemented SIP trunking on their Cisco UCM and reports that calls using the SIP trunk are using Media Termination Point resources unnecessarily. Which action resolves the issue?

A. Change DTMF Signaling Method to “No Preference”.

B. Disable SIP Rel1XX Options.

C. Change to a range that does not result in MTP.

D. Change DTMF Signaling Method to “RFC 4733”.

An engineer has two Cisco UCM clusters and wants them using ILS with TLS Certificates. Cluster A (Pub and 1 Subscriber) will be the hub, and Cluster B (Pub and 1 Subscriber) will be the spoke. Both clusters have self-signed certificates. The engineer has exchanged Publisher A and Subscriber B Tomcat certificates, but the connection fails. What is the cause of the failure?

A. The password is incorrect.

B. Cluster IDs are not unique.

C. The Tomcat certificate from Cluster B must be the Publisher.

D. The engineer needs to exchange the CallManager certificate.

What is the relationship between partition, time schedule, and time period in Time-of-Day routing in Cisco Unified Communications Manager?

A. A partition can have multiple time schedules assigned. A time schedule contains one or more time periods.

B. A partition can have one time schedule assigned. A time schedule contains one or more time periods.

C. A partition can have multiple time schedules assigned. A time schedule contains only one time period.

D. A partition can have one time schedule assigned. A time schedule contains only one time period.

Refer to the exhibit. How many maximum hops can an ILS updarte traverse?

A. 3

B. 6

C. 9

D. 12

A company was looking at the IT charges and saw many long-distance and international calls primarily to sites in North America and around the world. The administrator wants to optimize the PSTN expense. Which dial plan configuration reduces PSTN connectivity charges by using the IP network to bring the egress point to the PSTN as close as possible to the called number?

A. translation patterns

B. tail end hop off

C. client matter codes

D. dial rules

Users report strange behaviors when they call external numbers from the company phone system. The company is using Cisco 8865 phones with Cisco UCM connected to a gateway with two TI circuits. There is no indication of the possible problem, but the connection seems to be established. Which command meets the requirement to capture all the data needed to debug the problem?

A. debug mgcp media tracelevel critical

B. debug mgcp media tracelevel critical all

C. debug mgcp media tracelevel critical verbose

D. debug mgcp media tracelevel moderate

Which call pickup feature allows users to pick up incoming calls in a group that is associated with their own group?

A. Other Group Pickup

B. BLF Call Pickup

C. Group Call Pickup

D. Directed Call Pickup

Some users report having issues dialing some external numbers when traveling to other locations within the company. The company has five locations in five cities in one country and has an egress gateway in each location for TEHO. The configuration has no specific entry stating that the roaming users are using the local gateway, but calls are going out. How is a verification of the call routing in such a specific configuration performed to further identify the problem?

A. device mobility

B. standard local route group

C. local route groups

D. TEHO

Refer to the exhibit. A company is using Microsoft Teams with Cisco Unified Border Element integration, but the administrator sees a one-way audio issue with Microsoft Teams. The administrator must modify the SIP profile to send the proper information on the SDP for IP address for media to match the internal and external interface. Which set of commands resolves the issue?

A. voice class sip-profiles 1request INVITE sdp-header Connection-Info modify “2.76.1” “2.78.1”

B. voice class sip-profiles 1request INVITE sdp-header Session-Owner modify “27.0.0” “27.3.0”

C. voice class sip-profiles 1request INVITE sdp-header Connection add “2.76.1” “2.78.1”

D. voice class sip-profiles 1request INVITE sdp-header Audio-Attribute modify “2.76.1” “2.71.1”

In Cisco Unified Communications Manager, which tool do you use to check SIP traces?

A. MTP

B. CCSIP

C. RTMT

D. OS Administration Page

The Cisco Unified Communications Manager Dialed Number Analyzer allows analysis of calls from which two devices? (Choose two.)

A. translation patterns

B. device pools

C. CTI ports

D. CTI route points

E. IP phones

The company implemented Cisco Unified Mobility on the Cisco UCM. The users are satisfied and can transfer voice calls between devices. Mobile users want to extend the timer that controls the time given to pick up a voice call on an IP phone from 4 to 6 seconds. Which configuration change satisfies this requirement?

A. Change the “Maximum Wait Time for Desk Pickup” setting from 4 to 6

B. Change the “Maximum Wait Time for Mobility Pickup” setting from 4 to 6.

C. Change the “Maximum Wait Time for Mobility Pickup” setting from 4000 to 6000.

D. Change the “Maximum Wait Time for Desk Pickup” setting from 4000 to 6000.

You see the voice register pool 1 command in your Cisco Unified Communications Manager Express configuration. Which configuration is occurring in this section?

A. configuration for a single SIP phone

B. configuration items common for all SIP phones

C. configuration for a pool of SIP phones (similar to device pool on Cisco Unified Communications Manager)

D. configuration for SIP registrar service

When route patterns are defined as precisely as possible on a Cisco UCM, the control and reliability of the calling plan is increased. A route pattern must be added to support calls to this number range: 9135200 to 9135205. The calls are on-net and no translation patterns are configured. Which configuration meets these requirements?

A. 913520[012345]

B. 913520X

C. 913520[1–5]

D. 913520!

When configuring hunt groups, where do you add the individual directory numbers that will be part of the group?

A. route group

B. line group

C. hunt list

D. hunt pilot

What is first preference condition matched in a SIP-enabled incoming dial peer?

A. incoming uri

B. target carrier-id

C. answer-address

D. incoming called-number

Refer to the exhibit. Users report that when they dial to Cisco Unity Connection from an external network, they cannot enter any digits. Assuming only in-band
DTMF is supported, what is a reason for this malfunction?

A. The negotiated RTP port is outside of the range described by RFC, so inband DTMFs do not work.

B. There is SIP Delayed Offer. DTMF is supported only in Early Offer.

C. The rtpmap:0 value for the negotiated codec is marking DTMF as inactive.

D. No DTMF is negotiated.

A user requests a feature to send an active call to the mobile phone number on the physical phone. As an administrator, what should be configured in the Cisco UCM to accomplish this?

A. A Remote Destination Profile having the same extension as the physical phone’s Directory Number, add the mobile phone number to the RDP as a Remote Destination. Add the softkey “Join” to the physical phone’s softkey template.

B. A Remote Destination Profile having the same extension as the physical phone’s Directory Number, add the mobile phone number to the RDP as a Remote Destination. Add the softkey “Mobility” to the physical phone’s softkey template.

C. A Remote Destination Profile having the same extension as the Mobile phone’s number adds the physical phone’s Directory Number to the RDP as a Remote Destination. Add the softkey “Join” to the physical phone’s softkey template.

D. A Remote Destination Profile having the same extension as the Mobile phone’s number adds the physical phone’s Directory Number to the RDP as a Remote Destination. Add the softkey “Mobility” to the physical phone’s softkey template.

The sales department must answer phones when other sales members are not at their desks. The administrator knows that configuring Call Pickup allows the sales users to answer all the calls in the department by pressing only the softkey. Which call pickup configuration meets this requirement?

A. Standard Call Pickup

B. Group Call Pickup

C. Other Group Call Pickup

D. Directed Call Pickup