What is configured to use more than one port on the OEAP to extend the wired network?

A. remote LAN ACL

B. AAA override

C. client load balancing

D. remote LAN

An engineer is configuring location services with a Cisco CMX 10.6.2 solution. The engineer must strengthen interferer filtering so that Cisco CMX is protected from bursts of short-lived interferes. Which two interferer-filtering parameters must be configured to meet the requirement? (Choose two.)

A. Intensity Cutoff

B. Severity Cutoff

C. Duty Cycle Cutoff

D. RSSI Maximum

E. Utilization Maximum

When configuring a large, high-availability wireless network, which change to a mobility group creates less load on the controllers and maintains the same mobility messages?

A. Configure mobility group multicast messaging.

B. Remove unnecessary controllers from the mobility group.

C. Configure the controllers into separate RF groups from the mobility groups.

D. Separate the controllers into different mobility groups per controller.

What must be configured on ISE version 2.1 BYOD when using Single SSID?

A. open authentication

B. 802.1x

C. no authentication

D. WPA2

An engineer configures QoS on an AireOS WLC v8.5. The engineer configures a WLAN for voice traffic and must give a higher priority to WMM clients than to non-WMM clients. Which two configurations should be performed? (Choose two.)

A. Implement the Gold QoS profile.

B. Set Multicast Default Priority to Voice.

C. Set Unicast Default Priority to Platinum.

D. Select Video from the Unicast Default Priority drop-down menu.

E. Implement the Platinum QoS profile.

A network engineer observes a spike in controller CPU overhead and overall network utilization after multicast is enabled on a controller with 500 APs. Which feature corrects the issue?

A. controller IGMP snooping

B. multicast AP multicast mode

C. broadcast forwarding

D. unicast AP multicast mode

Split Tunneling must be configured for traffic sent by the client to be classified based on packet content, using an ACL. To accomplish this, the packets must be either locally switched from Cisco FlexConnect AP or centrally-switched over CAPWAP. Which type of ACL must be configured to accomplish this switching?

A. Interface

B. CPU

C. FlexConnect

D. WLAN

An engineer has configured Media Stream on the WLC and must guarantee at least 2 Mbps stream per user. Which RRC template should the engineer use?

A. coarse

B. medium

C. low

D. ordinary

A network engineer is configuring a Cisco FlexConnect AP to allow Cisco ISE to dynamically assign the subnet of a user based on their credentials. Which controller mapping must be modified for this feature?

A. WLAN VLAN

B. VLAN ACL

C. RF group

D. AP group

What is the difference between PIM sparse mode and PIM dense mode?

A. Sparse mode supports only one switch. Dense mode supports multiswitch networks.

B. Sparse mode floods. Dense mode uses distribution trees.

C. Sparse mode uses distribution trees. Dense mode floods.

D. Sparse mode supports multiswitch networks. Dense mode supports only one switch.

Refer to the exhibit. The image shows a packet capture that was taken at the CLI of the Cisco CMX server. It shows UDP traffic from the WLC coming into the server. What does the capture prove?

A. The Cisco CMX server receives NetFlow data from the WLC.

B. The Cisco CMX server receives NMSP traffic from the WLC.

C. The Cisco CMX server receives SNMP traffic from the WLC.

D. The Cisco CMX server receives Angle-of-Arrival data from the WLC.

An engineer is implementing Cisco Identity-Based Networking on a Cisco AireOS controller. The engineer has two ACLs on the controller. The first ACL, named
BASE_ACL, is applied to the corporate_clients interface on the WLC, which is used for all corporate clients. The second ACL, named HR_ACL, is referenced by
ISE in the Human Resources group policy. What is the resulting ACL when a Human Resources user connects?

A. HR_ACL appended with BASE_ACL

B. HR_ACL only

C. BASE_ACL appended with HR_ACL

D. BASE_ACL only

An engineer must create an account to log in to the CLI of an access point for troubleshooting. Which configuration on the WLC will accomplish this?

A. Allow New Telnet Sessions

B. ReadWrite User Access Mode

C. SNMP V3 User

D. Global Configuration Enable Password

A network engineer must configure APs on a controller for 802.1x access to a wired infrastructure as quickly as possible. The same credentials are used for all APs. Where are the credentials entered?

A. Management > Local Management Users

B. Security > Advanced EAP

C. AP > Credentials tab

D. Wireless > Global Configuration

Which two steps are needed to complete integration of the MSE to Cisco Prime Infrastructure to track the location of clients/rogues on maps? (Choose two.)

A. Synchronize access points with the MSE.

B. Add the MSE to Cisco Prime Infrastructure using the CLI credentials.

C. Add the MSE to Cisco Prime Infrastructure using the Cisco Prime Infrastructure communication credentials.

D. Apply a valid license for Wireless Intrusion Prevention System.

E. Apply a valid license for location tracking.

A customer is concerned that their wireless network is detecting spurious threats from channels that are not being used by their wireless infrastructure. Which two technologies must they deploy? (Choose two.)

A. FlexConnect mode

B. monitor mode

C. sniffer mode with no submode

D. local mode with WIPS submode

E. rogue detector mode

A network engineer is configuring a Cisco AireOS 8.2 WLC, Cisco MSE, and Cisco PI with Cisco 3700 Series APs and Cisco Hyperlocation modules. The engineer configures and enables a WLAN with Hyperlocation. During testing, the engineer notices that the Hyperlocation module cannot be seen on the WLC. Which action resolves the issue?

A. Configure the APs to be in monitor mode.

B. Enable Hyperlocation in the Global Configuration settings of the WLC.

C. Add the key hash that is used to add the Hyperlocation module to the WLC.

D. Enable the NTP server that is connected to the Hyperlocation module.

A wireless administrator receives this information to complete a CMX deployment in high availability by using version 10.6 to gather analytics.
• IP address of the primary server
• IP address of the secondary server
• failover mode to be configured as automatic
• root password of the secondary server
• email ID for NOC notifications
Enabling high availability fails when these parameters are used. Which action resolves the issue?

A. Insert the cmxadmin password of the secondary server.

B. Use IP protocol 4242 for the controller to reach the CMX server.

C. Place primary and secondary servers in different subnets.

D. Enable the virtual IP address of the primary server.

A network engineer needs to configure multicast in the network. The implementation will use multiple multicast groups and PIM routers. Which address provides automatic discovery of the best RP for each multicast group?

A. 224.0.0.13

B. 224.0.0.14

C. 224.0.1.39

D. 224.0.1.40

Refer to the exhibit. An engineer is creating an ACL to restrict some traffic to the WLC CPU. Which selection must be made from the direction drop-down list?
 

A. It must be Inbound because traffic goes to the WLC.

B. Packet direction has no significance; it is always Any.

C. It must be Outbound because it is traffic that is generated from the WLC.

D. To have the complete list of options, the CPU ACL must be created only by the CLI.

An engineer supports the network infrastructure within a football stadium, and there is a new requirement to send media over wireless. Multicast direct must be used to optimize multicast communication over wireless. Which multicast address must be added in the media stream configuration to meet this requirement?

A. WLC multicast address

B. video server multicast destination address

C. AP multicast address group

D. RP multicast address

An engineer configured a Cisco AireOS controller with two TACACS+ servers. The engineer notices that when the primary TACACS+ server fails, the WLC starts using the secondary server as expected, but the WLC does not use the primary server again until the secondary server fails or the controller is rebooted. Which cause of this issue is true?

A. Fallback is enabled

B. Fallback is disabled

C. DNS query is disabled

D. DNS query is enabled

Refer to the exhibit. An engineer is configuring a Cisco wireless LAN controller and needs wireless multicast to use the 54Mbps rates. Which action meets this requirement?

A. Change the 24 Mpbs to Supported.

B. Set all data rates below 54 Mbps to Supported.

C. Change the 54 Mpbs to Mandatory.

D. Set all data rates below 54 Mbps to Disable.

Refer to the exhibit. An engineer needs to manage non-802.11 interference. What is observed in the output on PI?

A. At least one strong interferer is impacting connectivity at this site.

B. Several light interferers are collectively impacting connectivity at this site.

C. The three individual clusters shown indicate poor AP placement.

D. RF at this site is unable to provide adequate wireless performance.

An engineer configures Cisco CMX. which uses Layer 2 high availability on primary and secondary CMX instances, according to these specifications:
• Primary CMX IP address: 192.168.1.4/24
• Secondary CMX IP address: 192.168.4.4/24
• Virtual IP address: 192.168.4.1/24
During testing, the engineer discovers that the failover fails. Which action resolves the issue?

A. Place the primary CMX IP address and the virtual IP address in the same subnet.

B. Place the secondary CMX IP address and the virtual IP address in different subnets.

C. Use a virtual IP address with CMX Layer 3 high availability.

D. Place the primary CMX IP address and the secondary CMX IP address in the same subnet.

Which two statements about the requirements for a Cisco Hyperlocation deployment are true? (Choose two.)

A. After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.

B. NTP can be configured, but that is not recommended.

C. The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.

D. The Cisco Hyperlocation feature must be enabled only on the wireless LAN controller.

E. If the Cisco CMX server is a VM, a high-end VM is needed for Cisco Hyperlocation deployments.

An IT administrator deploys Cisco 2802i APs in all office locations, including main campus and branch offices. The WLC that manages the APs is located at the data center on the main campus. The APs on the main campus are configured to use Local mode and the APs in the branches use FlexConnect mode. Which configuration must be applied to the APs for corporate devices on the main campus to be mapped to the local LAN switch on different VLANs according to the
VLAN tag ID and WLAN?

A. Enable Central DHCP Processing.

B. Disable FlexConnect Local Auth

C. Enable FlexConnect Local Switching.

D. Disable VLAN-based Central Switching.

An engineer completed the basic installation for two Cisco CMX servers and is in the process of configuring high availability, but it fails. Which two statements about the root of the issue are true? (Choose two.)

A. The Cisco CMX instances are installed in the same subnet.

B. The types of the primary and secondary Cisco CMX installations differ.

C. The delay between the primary and secondary instance is 200 ms.

D. The sizes of the primary and secondary Cisco CMX installations differ.

E. Both Cisco CMX installations are virtual.

An enterprise has recently deployed a voice and video solution available to all employees using AireOS controllers. The employees must use this service over their laptops, but users report poor service when connected to the wireless network. The programs that consume bandwidth must be identified and restricted.
Which configuration on the WLAN aids in recognizing the traffic?

A. NetFlow Monitor

B. AVC Profile

C. QoS Profile

D. Application Visibility

An engineer has implemented advanced location services for a retail wireless deployment. The marketing department wants to collect user demographic information in exchange for guest WLAN access and to have a customized portal per location hosted by the provider. Which social connector must be tied into
Cisco CMX to provide this service?

A. Gmail

B. Google+

C. Facebook

D. MySpace

On a Cisco Catalyst 9800 Series Wireless Controller, an engineer wants to prevent a FlexConnect AP from allowing wireless clients to connect when its Ethernet connection is nonoperational. Which command set prevents this connection?

A. config terminal wireless flexconnect profile [profile name] ethernet-fallback-enable end

B. config terminal wireless flexconnect profile [profile name] fallback-radio-shut end

C. config terminal wireless profile flex [profile name] fallback-radio-shut end

D. config terminal wireless profile flex [profile name] ethernet-fallback-enable end

An IT administrator deployed an OEAP to the home of a remote user, but the OEAP cannot reach the WLC. Which two configuration settings must be completed before an OEAP is deployed successfully? (Choose two.)

A. Configure Secondary Controller Name and Management IP address in the High Availability tab.

B. Configure LSC to authorize the OEAP.

C. Configure the AP mode to FlexConnect and check the box for Office Extend AP.

D. Configure the WLC with an external IP address on the virtual interface.

E. Configure Primary Controller Name and Management IP address in the High Availability tab.

What are two considerations when deploying a Cisco Hyperlocation? (Choose two.)

A. NTP configuration is available, but not recommended.

B. The Cisco Hyperlocation feature must be enabled only on the wireless LAN controller.

C. After enabling Cisco Hyperlocation on Cisco CMX, the APs and the wireless LAN controller must be restarted.

D. The Cisco Hyperlocation feature must be enabled on the wireless LAN controller and Cisco CMX.

E. If the Cisco CMX server is a VM, a high-end VM is needed for Cisco Hyperlocation deployments.

An engineer has eight WLCs in a mobility group and must reduce the bandwidth consumed. Which two configuration items achieve this result? (Choose two.)

A. global multicast mode

B. mobility group unicast messaging

C. global unicast messaging

D. mobility group multicast messaging

E. global symmetric mobility messaging

What is the maximum time range that can be viewed on the Cisco DNA Center issues and alarms page?

A. 3 hours

B. 24 hours

C. 3 days

D. 7 days

A corporation has recently implemented a BYOD policy at their HQ. Which two risks should the security director be concerned about? (Choose two.)

A. network analyzers

B. malware

C. lost and stolen devices

D. keyloggers

E. unauthorized users

Refer to the exhibit. An engineer must provide a position of rogue APs on a floor map using Cisco PI 3.0, but no rogue AP options are showing on the left-hand navigation menu under Maps. What is the reason for this omission?

A. An assurance license is not installed.

B. The controller operational status background task is disabled.

C. The Show Detected Interferers feature under the AP option is disabled.

D. Cisco MSE has not been added to Cisco PI.

The security policy mandates that only controller web management traffic is allowed from the IT subnet. In testing, an engineer is trying to connect to a WLAN with
Web Authentication for guest users, but the page is timing out on the wireless client browser. What is the cause of the issue?

A. The implemented CPU ACL on the controller is blocking HTTP/HTTPS traffic from the guest clients.

B. Web Authentication Redirect is not supported with CPU ACLs.

C. The DNS server that is configured on the controller is incorrect.

D. Web Authentication Redirect is supported only with Internet Explorer, and the client is using Google Chrome.

Refer to the exhibit. Which two items must be supported on the VoWLAN phones to take full advantage of this WLAN configuration? (Choose two.)

A. TSPEC

B. SIFS

C. 802.11e

D. WMM

E. APSD

Which QoS level is recommended for guest services?

A. gold

B. bronze

C. platinum

D. silver

An engineer must implement a wireless network to support location services. The network will include an MSE and Cisco WLC. After the deployment, the IT team must be able to locate and track clients. What is the minimum number of APs that a client must hear to accomplish this configuration so that the engineer can position them accordingly?

A. 1

B. 3

C. 4

D. 6

An engineer is in the process of implementing Fastiane on a wireless network with a Mobility Express AP installed and Apple end-user devices. Due to a security concern, the IT department has updated all the iPads to version 14.5.423551943. Which QoS profile must the engineer configure on the user WLAN?

A. Platinum

B. Best Effort

C. Bronze

D. Silver

The IT manager is asking the wireless team to get a report for all guest user associations during the past two weeks. In which two formats can Cisco Prime save this report? (Choose two.)

A. CSV

B. PDF

C. XLS

D. DOC

E. plain text

Which statement about the VideoStream/Multicast Direct feature is true?

A. IP multicast traffic is reliable over WLAN by default as defined by the IEEE 802.11 wireless multicast delivery mechanism.

B. Each VideoStream client acknowledges receiving a video IP multicast stream.

C. It converts the unicast frame to a multicast frame over the air.

D. It makes the delivery of the IP multicast stream less reliable over the air, but reliable over Ethernet.

An engineer is trying to log in to their lightweight access point joined to a WLC that does not have AP credentials defined. Which credentials does the engineer use?

A. admin/Cisco123

B. Cisco/Cisco

C. TACACS credentials

D. AP Global Configuration configured credentials

An engineer wants to configure WebEx to adjust the precedence and override the QoS profile on the WLAN. Which configuration is needed to complete this task?

A. Change the WLAN reserved bandwidth for WebEx

B. Create an AVC profile for WebEx

C. Create an ACL for WebEx

D. Change the AVC application WebEx-app-sharing to mark

A customer must use deep-packet inspection on the Cisco Catalyst 9800 Series Wireless Controller. The details must include all wireless client use details. Where must AVC be configured to meet this requirement?

A. AP join tag

B. policy profile

C. RF tag

D. WLAN

Which devices can be tracked with the Cisco Context Aware Services?

A. wired and wireless devices

B. wireless devices

C. wired devices

D. Cisco certified wireless devices

An enterprise started using WebEx as a virtual meeting solution. There is a concern that the existing wireless network will not be able to support the increased amount of traffic as a result of using WebEx. An engineer needs to remark the QoS value for this application to ensure high quality in meetings. What must be implemented to accomplish this task?

A. QoS preferred call index

B. UP to DSCP map

C. AVC profiles

D. WLAN quality of service profile

More people are working from home, so an engineer must configure OEAPs to support the users. The security team already configured NAT with a public IP address that points to the internal WLC IP address. The APs also have been configured with the public WLC IP address, but APs cannot join the controller yet. Which action resolves this issue?

A. Configure the internal WLC IP address on the OEAPs.

B. Create an ACL in WLC to accept the OEAPs.

C. Enable NAT on the WLC to configure the public IP address.

D. Configure the public WLC IP address on the home router.