Refer to the exhibit. The Internet traffic should always prefer Site-A ISP-1 if the link and BGP connection are up; otherwise, all Internet traffic should go to ISP-2.
Redistribution is configured between BGP and OSPF routing protocols, and it is not working as expected.
What action resolves the issue?

A. Set OSPF Cost 200 at Site-A RTR1, and set OSPF Cost 100 at Site-B RTR2.

B. Set metric-type 2 at Site-A RTR1, and set metric-type 1 at Site-B RTR2.

C. Set metric-type 1 at Site-A RTR1, and set metric-type 2 at Site-B RTR2.

D. Set OSPF Cost 100 at Site-A RTR1, and set OSPF Cost 200 at Site-B RTR2.

What is a MPLS PHP label operation?

A. Downstream node signals to remove the label.

B. It uses implicit-NULL for traffic congestion from source to destination forwarding.

C. PE removes the outer label before sending to the P router.

D. It improves P router performance by not performing multiple label lookup.

Refer to the exhibit. Routing protocols are mutually redistributed on R3 and R1. Users report intermittent connectivity to services hosted on the 10.1.1.0/24 prefix.
significant routing update changes are noticed on R3 when the show ip route profile command is run.
How must the services be stabilized?

A. The routing loop must be fixed by reducing the admin distance of OSPF from 110 to 80 on R3

B. The routing loop must be fixed by reducing the admin distance of iBGP from 200 to 100 on R3

C. The issue with using BGP must be resolved by using another protocol and redistributing it into EIGRP on R3

D. The issue with using iBGP must be fixed by running eBGP between R3 and R4

With Internal BGP, there is a requirement for all peers to be logically fully meshed, where all IBGP routers must peer with all other IBGP routers. For scaling purposes, there are two mechanisms that were developed to bypass this requirement. What are they? (Choose two.)

A. Confederations

B. IBGP to EBGP route redistribution

C. BGP peer filtering

D. Route reflectors.

Refer to the exhibit. An administrator is attempting to disable the automatic logout after a period of inactivity. After logging out, the console stopped responding to all keyboard inputs. Remote access through SSH still works.
Which action resolves the issue?

A. configure the no exec-timeout command on line con 0.

B. configure the absolute-timeout command on line con 0.

C. configure the exec command on line con 0.

D. configure the default exec-timeout command on line con 0

Refer to the exhibit. Which configuration resolves the IP SLA issue from R1 to the server?

A. R6(config)#ip sla responder

B. R6(config)#ip sla 650 R6(config-ip-sla)#udp-jitter 10.60.60.6

C. R6(config)#ip sla responder udp-echo ipaddress 10.60.60.6 po 5000

D. R6(config)#ip sla schedule 10 life forever start-time now

Refer to the exhibit. Which configuration enables OSPF for area 0 interfaces to establish adjacency with a neighboring router with the same VRF?

A. router ospf 1 vrf CCNP network 10.1.1.1 0.0.0.0 area 0 network 10.2.2.2 0.0.0.0 area 0

B. router ospf 1 interface Ethernet1 ip ospf 1 area 0.0.0.0 interface Ethernet2 ip ospf 1 area 0.0.0.0

C. router ospf 1 vrf CCNP interface Ethernet1 ip ospf 1 area 0.0.0.0 interface Ethernet2 ip ospf 1 area 0.0.0.0

D. router ospf 1 vrf CCNP network 10.0.0.0 0.0.255.255 area 0

Refer to the exhibit. An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock.
What is the reason for this error?

A. An authentication error with the NTP server results in an incorrect timestamp.

B. The keyword localtime is not defined on the timestamp service command.

C. The NTP server is in a different time zone.

D. The system clock is set incorrectly to summer-time hours.

What is considered the primary advantage of running BFD?

A. reduction in time needed to detect Layer 3 routing neighbor failures

B. reduction in CPU needed to detect Layer 3 routing neighbor failures

C. reduction in time needed to detect Layer 2 switched neighbor failures

D. reduction in CPU needed to detect Layer 2 switch neighbor failures

An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency. The output of the show ip ospf neighbor command shows that the neighbor state is EXSTART/EXCHANG

A. Which action should be taken to resolve this issue?

B. match the passwords

C. match the hello timers

D. match the MTUs

E. match the network types

Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.

Select and Place:

Refer to the exhibit. An engineer must configure router R101 for SSH access on ports 2001 through 2011. After the configuration, some expected ports were inaccessible. Which command resolves the issue?

A. ip ssh port 2001 rotary 11
line vty 0 4
transport input telnet

B. ip ssh port 2000 rotary 11
line vty 0 4
transport input ssh

C. ip ssh port 2000 rotary 1 11
line vty 0 4
transport input all

D. ip ssh port 2001 rotary 1 11
line vty 0 4
transport input ssh

What is an advantage of MPLS Layer 3 VPN deployment?

A. Planning and modifications are required for the customer intranet before migrating to Layer 3 VPN.

B. Scalable VPNs are created using connection-oriented, point-to-point, or multipoint overlay connections.

C. QoS provides performance with policy and support for a best-effort service level in an MPLS VPN.

D. Security is provided at the edge of the provider network through encryption.

Refer to the exhibit. A network engineer configured routers R1 and R2 with MP-BGP. The engineer noticed that the routers cannot exchange any IPv6 routes; however, the IPv4 neighbor relationship is working ne. Which configuration must the engineer apply to router R2 to exchange IPv6 routes?

A.

B.

C.

D. B

Refer to the exhibit. After an engineer configured a new Cisco router as a DHCP server, users reported two primary issues:
• Devices in the HR subnet have intermittent connectivity problems.
• Workstations in the LEGAL subnet cannot obtain IP addresses.
Which configurations must the engineer apply to ROUTER_1 to restore connectivity for the affected devices?

A.

B.

C.

D.

Refer to the exhibit. A network engineer configured routers R1 and R2 with MP-BGP. The engineer noticed that the routers cannot exchange any IPv6 routes; however, the IPv4 neighbor relationship is working fine.
Which configuration must the engineer apply to router R2 to exchange IPv6 routes?

A. ipv6 unicast-routingipv6 cef!interface Loopback100ipv6 address 2001:DB8:128::2/128!interface GigabitEthernet1/0ipv6 address 2001:DB8:1::2/64!router bgp 65002no bgp default ipv4-unicastneighbor 2001:DB8:1::1 remote-as 65001!address-family ipv4network 2001:DB8:128::2/128

B. ipv6 unicast-routingipv6 cef!interface Loopback100ipv6 address 2001:DB8:128::2/128!interface GigabitEthernet1/0ipv6 address 2001:DB8:1::2/64!router bgp 65002no bgp default ipv4-unicastneighbor 2001:DB8:1::1 remote-as 65001!address-family ipv6network 2001:DB8:128::2/128

C. ipv6 unicast-routingipv6 cef!interface Loopback100ipv6 address 2001:DB8:128::2/128!interface GigabitEthernet1/0ipv6 address 2001:DB8:1::2/64description AS65001 ID B468^AD03G907::1!router bgp 65002no bgp default ipv4-unicastneighbor 2001:DB8:1::1 remote-as 65001!address-family ipv6network 2001:DB8:128::2/128neighbor 2001:DB8:1::1 activate

D. ipv6 cef!interface Loopback100ipv6 address 2001:DB8:128::2/128!interface GigabitEthernet1/0ipv6 address 2001:DB8:1::2/64!router bgp 65002no bgp default ipv4-unicastneighbor 2001:DB8:1::1 remote-as 65001!address-family ipv6network 2001:DB8:128::2/128neighbor 2001:DB8:1::1 activate

An engineer is trying to copy an IOS file from one router to another router by using TFTP.
Which two actions are needed to allow the file to copy? (Choose two.)

A. Copy the file to the destination router with the copy tftp: flash: command

B. Enable the TFTP server on the source router with the tftp-server flash: < lename> command

C. TFTP is not supported in recent IOS versions, so an alternative method must be used

D. configure a user on the source router with the username tftp password tftp command

E. configure the TFTP authentication on the source router with the tftp-server authentication local command AB

Refer to the exhibit. An engineer wanted to set a tag of 30 to route 10.1.80.65/32 but it failed.
How is the issue fixed?

A. Modify route-map ospf-to-eigrp permit10 and match prefix-list ccnp2.

B. Modify prefix-list ccnp3 to add 10.1.64.0/20 ge 32.

C. Modify prefix-list ccnp3 to add 10.1.64.0/20 file 24.

D. Modify route-map ospf-to-eigrp permit 30 and match prefix-list ccnp2.

Which of the following OSPF neighbor adjacency states is applicable only to manually configured OSPF neighbors in a Non Broadcast Multi- Access network?

A. Attempt

B. Init

C. 2-Way

D. Exstart

E. Exchange

Refer to the exhibit.

A network is under a cyberattack. A network engineer connected to R1 by SSH and enabled the terminal monitor via SSH session to find the source and destination of the attack. The session was flooded with messages, which made it impossible for the engineer to troubleshoot the issue.
Which command resolves this issue on R1?

A. (config)#terminal no monitor

B. (config)#no terminal monitor

C. #no terminal monitor

D. #terminal no monitor

Which table is used to map the packets in an MPLS LSP that exit from the same interface, via the same next hop, and have the same queuing policies?

A. LDP

B. FEC

C. CEF

D. RIB

Refer to the exhibit. Bangkok is using ECMP to reach to the 192.168.5.0/24 network. The administrator must configure Bangkok in such a way that Telnet traffic from 192.168.3.0/24 and 192.168.4.0/24 networks use the Hong Kong router as the preferred route. Which set of configurations accomplishes this task?

A. access-list 101 permit tcp 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23 access-list 101 permit tcp 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
interface Ethernet0/1
ip policy route-map PBR1

B. access-list 101 permit tcp 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23 access-list 101 permit tcp 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255 eq 23
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
interface Ethernet0/3
ip policy route-map PBR1

C. access-list 101 permit ip 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255 access-list 101 permit ip 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
interface Ethernet0/3
ip policy route-map PBR1

D. access-list 101 permit ip 192.168.3.0 0.0.0.255 192.168.5.0 0.0.0.255 access-list 101 permit ip 192.168.4.0 0.0.0.255 192.168.5.0 0.0.0.255
route-map PBR1 permit 10
match ip address 101
set ip next-hop 172.18.1.2
interface Ethernet0/1
ip policy route-map PBR1

Refer to the exhibit. An engineer configured SNMP traps to record spoofed packets drop of more than 48000 a minute on the ethernet0/0 interface. During an IP spoofing attack, the engineer noticed that no notifications have been received by the SNMP server. Which configuration resolves the issue on R1?

A. ip verify unicast notification threshold 800

B. ip verify unicast notification threshold 8000

C. ip verify unicast notification threshold 48000

D. ip verify unicast notification threshold 80

Refer to the exhibit. The engineer is reviewing the logs on the DENVER router and notices that this error message repeats constantly:
*Jun 12 13:42:03.399: %TCP-6-BADAUTH: No MD5 digest from 10.40.1.1(27174) to 10.40.1.2(179) tableid - 0
Which action resolves the issue?

A. Configure OSPF link authentication on the router with IP address 10.40.1.1.

B. Configure NTP authentication on the router with IP address 10.40.1.1.

C. Configure BGP authentication on the router with IP address 10.40.1.2.

D. Configure BGP authentication on the router with IP address 10.40.1.1.

Network operations report issues with receiving too many external routes, which caused CPU spike on routers with smaller memories. Which action resolves the issue?

A. configure the area range command when redistributing on ASBR.

B. configure the summary-address command when redistributing on ABR.

C. configure the area range command when redistributing on ABR.

D. configure the summary-address command when redistributing on ASBR.

Refer to the exhibit. A network engineer notices that the configured track option is down. Which configuration resolves the issue?

A. ip sla schedule 10 start-time pending life forever

B. ip sla schedule 10
no timeout

C. ip sla schedule 10 start-time now

D. ip sla schedule 10
no threshold

What is a prerequisite for configuring BFD?

A. Jumbo frame support must be configured on the router that is using BF

B. All routers in the path between two BFD endpoints must have BFD enabled.

C. Cisco Express Forwarding must be enabled on all participating BFD endpoints.

D. To use BFD with BGP, the timers 3 9 command must first be configured in the BGP routing process.

Refer to the exhibit. The administrator configured the network devices for end-to-end reachability, but the ASBRs are not propagating routes to each other. Which set of configurations resolves this issue?

A. router bgp 100
neighbor 10.1.1.1 next-hop-self
neighbor 10.1.2.2 next-hop-self
neighbor 10.1.3.3 next-hop-self

B. router bgp 100
neighbor 10.1.1.1 update-source Loopback0
neighbor 10.1.2.2 update-source Loopback0
neighbor 10.1.3.3 update-source Loopback0

C. router bgp 100
neighbor 10.1.1.1 route-reflector-client
neighbor 10.1.2.2 route-reflector-client
neighbor 10.1.3.3 route-reflector-client

D. router bgp 100
neighbor 10.1.1.1 ebgp-multihop
neighbor 10.1.2.2 ebgp-multihop
neighbor 10.1.3.3 ebgp-muttihop

Refer to the exhibit. An engineer configured NetFlow but cannot receive the ows from R1. Which two configurations resolve the issue? (Choose two.)

A. R3(config)#ip access-list extended DDOS
R3(config-ext-nacl)#5 permit udp any host 10.66.66.66 eq 1090

B. R4(config)# flow exporter FlowExporter1
R4(config- flow-exporter)#destination 10.66.66.66

C. R3(config)# flow exporter FlowExporter1
R3(config- flow-exporter)#destination 10.66.66.66

D. R1(config)# flow exporter FlowExporter1
R1(config- flow-exporter)#destination 10.66.60.66

E. R4(config)#ip access-list extended DDOS
R4(config-ext-naci)#5 permit udp any host 10.66.66.66 eq 1090

Refer to the exhibit. traffic from R3 to the central site does not use alternate paths when R3 cannot reach 10.10.10.2. traffic on R3 destined to R4 takes an alternate route via 10.10.10.6 when 10.10.10.4 is not accessible from R3. Which configuration switches traffic destined to 10.10.10.2 from R3 on the alternate path?

A. R3(config)#ip route 192.168.10.1 255.255.255.255 10.10.10.2 track 20

B. R6(config)#ip route 10.10.10.3 255.255.255.255 10.0.0.30

C. R3(config)#track 20 ip sla 20 reachability

D. R2(config)#ip route 10.10.10.3 255.255.255.255 10.0.0.6

What are two purposes of using IPv4 and VPNv4 address-family configurations in a Layer 3 MPLS VPN? (Choose two.)

A. RD is prepended to the IPv4 route to make it unique.

B. The VPNv4 address consists of a 64-bit route distinguisher that is prepended to the IPv4 prefix.

C. MP-BGP is used to allow overlapping IPv4 addresses between customers to advertise through the network.

D. The IPv4 address is needed to tag the MPLS label.

E. The VPNv4 address is used to advertise the MPLS VPN label.

Refer to the exhibit. R2 has two paths to reach 192.168.13.0/24, but traffic is sent only through R3.
Which action allows traffic to use both paths?

A. configure the variance 4 command under the EIGRP process on R2.

B. configure the bandwidth 2000 command under interface FastEthernet0/0 on R2.

C. configure the delay 1 command under interface FastEthernet0/0 on R2.

D. configure the variance 2 command under the EIGRP process on R2.

In a DMVPN network, the Spoke1 user observed that the voice traffic is coming to Spoke2 users via the hub router. Which command is required on both spoke routers to communicate directly to one another?

A. ip nhrp nhs multicast

B. ip nhrp shortcut

C. ip nhrp map dynamic

D. ip nhrp redirect

Refer to the exhibit. A router is receiving BGP routing updates from multiple neighbors for routes in AS 690. What is the reason that the router still sends traffic that is destined to AS 690 to a neighbor other than 10.222.1.1?

A. The local preference value in another neighbor statement is higher than 250.

B. The local preference value should be set to the same value as the weight in the route map.

C. The route map is applied in the wrong direction.

D. The weight value in another neighbor statement is higher than 200.

Drag and drop the MPLS terms from the left onto the correct definitions on the right.

Select and Place:

Which two components are needed for a service provider to utilize the L3VPN MPLS application? (Choose two.)

A. The P routers must be configured with RSVP.

B. The PE routers must be configured for MP-eBGP to connect toffices.

C. The P routers must be configured for MP-iBGP toward the PE routers.

D. The PE routers must be configured for MP-iBGP with other PE routers.

E. The P and PE routers must be configured with LDP or RSVP.

Refer to the exhibits. An engineer investigates a routing issue on R1 and finds that traffic destined to 5.5.5.0/24 does not take all of the paths.
Which action resolves the issue?

A. Increase the variance value in EIGRP.

B. Decrease the variance value in EIGRP.

C. Remove the adjacency of R3 from EIGRP.

D. Stop advertising 192.168.13.0/24 in EIGRP.

20mechanism%20to,means%20equal%2Dcost%20load%20balancing

Users report web connectivity problems on the server (10.1.1.10). Which IP SLA configuration captures the failure details through the network to resolve the issue?

A.

B.

C.

D.

Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server. RouterB is configured as follows:

Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?

A. RouterB(config-if)#ip helper-address 172.16.1.1

B. RouterB(config-if)#ip helper-address 255.255.255.255

C. RouterB(config-if)#ip helper-address 172.16.1.2

D. RouterB(config-if)#ip helper-address 172.31.1.1

Which configuration enables the VRF that is labeled `Inet` on FastEthernet0/0?

A. R1(config)# ip vrf Inet R1(config-vrf)#ip vrf FastEthernet0/0

B. R1(config)#ip vrf Inet FastEthernet0/0

C. R1(config)# ip vrf Inet R1(config-vrf)#interface FastEthernet0/0 R1(config-if)#ip vrf forwarding Inet

D. R1(config)#router ospf 1 vrf Inet R1(config-router)#ip vrf forwarding FastEthernet0/0

Refer to the exhibit. An engineer configured IP SLA to monitor a next hop on a router for reachability. When the next hop is unreachable, the router is executing tracking and falling over another route, but packet loss is experienced because the reachability is flapping. Which action resolves the issue?

A. Increase the frequency of the sla probe to 60.

B. Append delay up 60 down 60 to the track command.

C. Append delay up 0 down 0vto the track command.

D. Increase the timeout of the sla probe to 6000.

Refer to the exhibit. R1 is configured with uRPF, and ping to R1 is failing from a source present in the R1 routing table via the GigabitEthernet 0/0 interface. Which action resolves the issue?

A. Enable Cisco Express Forwarding to ensure that uRPF is functioning correctly.

B. Modify the uRPF mode from strict to loose.

C. Add a floating static route to the source on R1 to the GigabitEthernet0/1 interface.

D. Remove the access list from the interface GigabitEthernet 0/0.

The network administrator configured CoPP so that all SNMP traffic from Cisco Prime located at 192.168.1.11 toward the router CPU is limited to 1000 kbps. Any traffic that exceeds this limit must be dropped.
access-list 100 permit udp any any eq 161
class-map CM-SNMP
match access-group 100
policy-map PM-COPP
class CM-SNMP
police 1000 conform-action transmit
control-plane
service-policy input PM-COPP
The network administrator is not getting the desired result for the SNMP traffic and SNMP traffic is getting dropped frequently. Which set of configurations resolves the issue?

A. no access-list 100
access-list 100 permit tcp host 192.168.1.11 any eq 161

B. no access-list 100
access-list 100 permit udp host 192.168.1.11 any eq 161
policy-map PM-COPP
class CM-SNMP
no police 1000 conform-action transmit
police 1000000 conform-action transmit
control-plane
no service-policy input PM-COPP
interface E 0/0
service-policy input PM-COPP
interface E 0/1
service-policy input PM-COPP

C. no access-list 100
access-list 100 permit udp host 192.168.1.11 any eq 161
policy-map PM-COPP
class CM-SNMP
no police 1000 conform-action transmit
police 1000000 conform-action transmit

D. policy-map PM-COPP
class CM-SNMP
no police 1000 conform-action transmit
police 1000000 conform-action transmit

A newly installed spoke router is configured for DMVPN with the ip mtu 1400 command. Which configuration allows the spoke to use fragmentation with the maximum negotiated TCP MTU over GRE?

A. ip tcp adjust-mss 1360 crypto ipsec fragmentation mtu-discovery

B. ip tcp adjust-mss 1360 crypto ipsec fragmentation after-encryption

C. ip tcp payload-mtu 1360 crypto ipsec fragmentation after-encryption

D. ip tcp payload-mtu 1360 crypto ipsec fragmentation mtu-discovery

Refer to the exhibit. Two routers are connected back to back via Gigabit Ethernet 0/0 interfaces. Which configuration provides VRF-Lite connectivity for two separate VRFs using the prefixes 10.1.1.0/24 for one VRF and 10.2.2.0/24 for the other VRF?

A. ip vrf 1
rd 65001:1
ip vrf 2
rd 65001:2
int GigabitEthernet0/0
no shut
int GigabitEthernet0/0.1
encapsulation dot1Q 1
ip vrf forwarding
ip address 10.1.1.1 255.255.255.0
int GigabitEthernet0/0.2
encapsulation dot1Q 2
ip vrf forwarding
ip address 10.2.2.1 255.255.255.0

B. ip vrf 1
rd 65001:1
ip vrf 2
rd 65001:1
int GigabitEthernet0/0
no shut
int GigabitEthernet0/0.1
encapsulation dot1Q 1
ip vrf forwarding 1
ip address 10.1.1.1 255.255.255.0
int GigabitEthernet0/0.2
encapsulation dot1Q 2
ip vrf forwarding 2
ip address 10.2.2.1 255.255.255.0

C. ip vrf 1
ip vrf 2
int GigabitEthernet0/0
no shut
int GigabitEthernet0/0.1
encapsulation dot1Q 1
ip vrf forwarding 1
ip address 10.1.1.1 255.255.255.0
int GigabitEthernet0/0.2
encapsulation dot1Q 2
ip vrf forwarding 2
ip address 10.2.2.1 255.255.255.0

D. ip vrf 1
ip vrf 2
int GigabitEthernet0/0
no shut
int GigabitEthernet0/0.1
encapsulation dot1Q 1
ip address 10.1.1.1 255.255.255.0
ip vrf forwarding 1
int GigabitEthernet0/0.2
encapsulation dot1Q 2
ip address 10.2.2.1 255.255.255.0
ip vrf forwarding 2

In order to connect between disparate OSPF and EIGRP portions of a network, mutual route redistribution has been configured. What are two disadvantages of doing this? (Choose two.)

A. Prone to routing loops if not done correctly

B. Differing metrics between the routing protocols could result in sub-optimal routing.

C. Route redistribution is not supported on most Cisco router platforms.

D. Increased convergence times.

Refer to the exhibit. Router R2 should be learning the route for 10.123.187.0/24 via EIGRP. Which action resolves the issue without introducing more issues?

A. Redistribute the route in EIGRP with metric, delay, and reliability.

B. Use distribute-list to modify the route as an internal EIGRP route.

C. Use distribute-list to filter the external routes in OSP

D. Remove route redistribution in R2 for this route in OSP

E.

Which feature of the Cisco DNA Center allows you to run diagnostic CLI commands to the devices that are managed by DNA Center for troubleshooting purposes?

A. Command Runner

B. DNA Spaces

C. DNA Advantage

D. Intelligent Capture

Refer to the exhibit. R1 lost its directly connected EIGRP peer 172.16.33.2 (SW1). Which configuration resolves the issue?

A.

B.

C.

D. C

Refer to the exhibit.

An engineer observes that every time the ICMP packet is lost at a polling interval, track 1 goes down, which causes unnecessary disruption and instability in the network. The engineer does not want the traffic to be rerouted if the loss of ICMP packets is negligible. If the packet loss is persistent for a longer duration, the track must go down and the traffic must be rerouted. Which action resolves the issue?

A. Change the IP SLA schedule to run only at certain intervals.

B. Increase the timeout value from 1000 to 1500.

C. define a delay timer under track 1.

D. Increase the threshold value from 1000 to 1500.